Dannmar D2-12C Installation And Operation Manual Download Page 5

5

INSTALLER / OPERATOR

PLEASE READ AND FULLY UNDERSTAND. 

BY PROCEEDING YOU AGREE TO THE 

FOLLOWING:

I have visually inspected the site where the lift is to 

be installed and verified the concrete to be in good condi-
tion and free of cracks or other defects. I understand that 
installing a lift on cracked or defective concrete could 
cause lift failure resulting in personal injury or death.

I understand that a level floor is required for proper 

installation and level lifting. 

I understand that I am responsible if my floor is of 

questionable slope and that I will be responsible for all 
charges related to pouring a new level concrete slab if 
required and any charges.

t

   I understand that Dannmar lifts are supplied with  

concrete fasteners meeting the criteria of the latest ver-
sion of the American National Standard “Automotive 
Lifts - Safety Requirements for Construction, Testing, and 
Validation” ANSI/ALI ALCTV and that I will be responsible 
for all charges related to any special regional structural 
and/or seismic anchoring requirements specified by any 
other agencies and/or codes such as the Uniform Building 
Code (UBC) and/or International Building Code (IBC).

I assume full responsibility for the concrete floor and 

condition thereof, now or later, where the above equip-
ment model(s) are to be installed. Failure to follow warning 
symbols may lead to serious personal injury or death to 
operator or bystander or damage to property. 

I understand that Dannmar lifts are designed to be 

installed in indoor locations only. Failure to follow instal-
lation instructions may lead to serious personal injury or 
death to operator or bystander or damage

 

to property or 

lift.

Failure to follow danger, warning, and caution        

instructions may lead to serious personal injury or death 

to operator or bystander or damage to property. 

Please read entire manual prior to installation. Do not 

operate this machine until you read and understand 

all the dangers, warnings and cautions in this manual. 

For additional copies or further information, contact:

BendPak Inc. / Dannmar Products

1645 Lemonwood Dr.

Santa Paula, CA. 93060 

(877) 432-6627

www.dannmar.com

INSTALLER / OPERATOR 

PROTECTIVE EQUIPMENT

You 

MUST

 wear OSHA-approved (publication 3151) 

Personal Protective Equipment 

at all times

 when  

installing the Lift. Leather gloves, steel-toed work boots, 

eye protection, back belts, and hearing protection 

are 

mandatory

.

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED

COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OR YOURSELF AND OTHERS

AND CAN CAUSE PERSONAL INJURY OR DEATH.  READ AND FOLLOW ALL INSTRUCTIONS IN

THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.

Summary of Contents for D2-12C

















































Reviews: