background image

 

Configuring of an alarm text 

The alarm text is configured by sending a text message to the Epi-Care® 

free

’s 

phone 

number. The message must start with the text “sat1”, followed by a short 

text, for example a name. The alarm text can contain up to 18 characters, 
including letters, numbers and spaces. 

Example: sat1 John Smith 

The alarm text is shown in the text message, are sent during an alarm, and in 
messages about possible service disruptions. 
Configuration of the alarm text can be omitted, if a text message is not needed. 

 
 

 

Configuring of backup number 

If a backup number is configured, the Epi-Care® 

free

 will direct alarm calls 

to the backup number, if the alarm number does not pick up. Configure the 
backup number by sending a text message 

with the text “sab1”, followed by 

the backup number. 

Example: sab1 22334455 

Configuration of a backup number can be omitted, if it is not needed. 

 
 

 

Checking configuration 

There are two ways to check the configured alarm number, alarm text and 
backup number. The first approach is to enter 

the control unit’s menu “GSM 

INFO”. 

It is also possible to check the configuration by sending a text message to the Epi-
Care® 

free’s 

phone number. The message must start with the text “gau1”. 

After approximately one minute, the unit will reply with a text message 
containing the information stored on the unit. 

 
 

 

Deleting the configured information 

The stored information is deletable by sending the following text messages to the 
control unit’s phone number:  
Delete alarm number: san1 
Delete alarm text: sat1 
Delete backup number: sab1 
 
Old information is automatically deleted, when new information is configured.  
 
An alarm number MUST always be configured. 

Summary of Contents for Epi-Care free

















Reviews: