background image

Specifications

Description

Minimum

Maximum

Comment

EEPROM write/erase cycles

1 million

Minimum valid over entire operating temperature
range.

EEPROM used in PLUS+1

®

 controllers is rated for one million read/write cycles per sector. Sector size is 32

bits. When a value is written to EEPROM, all 32 bits in a particular sector are always written, regardless of
the size of the size of the saved value. If the value being saved in a sector is less than 32 bits (such as U8,
S16, BOLL) adjacent bits in the same EEPROM sector are rewritten with their previous value. The
implication of this memory property is that if two values are being written to the same memory sector,
the useful life of the sector is determined by the value being written most frequently. If that value
exceeds 1 million read/write cycles, all values in the sector may be compromised if the useful life is
exceeded.

Environmental testing criteria

General product ratings

Description

Units

Minimum

Maximum

Comment

Operating temperature

˚C [˚F]

-40 [-40]

85 [185]

Storage temperature

˚C [˚F]

-40 [-40]

85 [185]

Allowable module supply voltage

Vdc

7

36

Module sensor supply voltage

Vdc

3

12

Sensor voltage drops below the minimum value if
module supply voltage < 7 Vdc. See 

Sensor power supply

ratings

 on page 19.

Analog input voltage levels

Vdc

36

Allowable output load current 
(per pin)

A

See individual module date sheets.

Module allowable total output current

A

See individual module data sheets.

All modules Ingress Protection (IP) rating

*

IP 67

All modules CE rating

CE compliant.

*

 The PLUS+1

®

 modules IP 67 rating is only valid when the module mating connector is in place and unused connector pin positions have sealing plugs

installed.

SC Controller Family environmental testing criteria

Climate environment

Description

Applicable standard

Comment

Storage temperature

IEC 60068-2-1, test Ab, IEC 60068-2-2
test Bb

Operating temperature

IEC 60068-2-1, test Ab, IEC 60068-2-2
test Bd

Thermal cycle

IEC 60068-2-2, test Na, IEC
60068-2-38 (partial)

Humidity

IEC 60068-2-78, IEC 60068-2-30 test
Db

Damp heat steady state and cyclic.

Degree of protection

IEC 60529

Technical Information

PLUS+1 SC0XX-1XX Controller Family

Product ratings

 

20 | 

©

 Danfoss | June 2016

L1415500 | BC00000235en-US0201

Summary of Contents for PLUS+1 SC0XX-1 Series





























Reviews: