Dane Technologies WM2000 Owner'S Manual Download Page 32

Page: 32 / 79

Dane Technologies, Inc.

WheelChair Mover

Owners Manual

7105 Northland Terrace, Minneapolis, MN 55428 / 888-544-7779 / 763-544-7779 / Fax 763-544-4234

www.danetechnologies.com

970-068 6/19/17 Rev F

Qualified facility maintenance technician
repairable items:

These items must be kept in

good repair to insure continued warranty
coverage. All other parts are not to be repaired by
the user.

No items are repairable by the operator.

Tires

Casters

Battery Charger
Battery Charger Power Cord
Batteries

Jaws

Anti-static wire

Some parts on the WheelChair Mover are rebuildable but all of those parts require a
qualified facility maintenance technician or a Dane Technologies authorized service
technician to do the removal and replacement of the part.

Maintenance Items:

Tires

Casters

Batteries

Jaws

Anti-static wire

Technician tools list:

Needle nose pliers (caster cleaning)

Mechanics knife (caster axle cover)
#2 Phillips screwdriver (anti-static wire)

T20 Torx (front, back covers)
T27 Torx (wheel side covers)

7/16” socket (jaws, battery hold down, front wheel nuts)

1/2” socket (caster wheel axle)

9/16” socket (battery cable)

3/4" socket (caster swivel)

Torque wrench

Loctite 222

Summary of Contents for WM2000
















































































Search results

Summary of Contents for WM2000

Reviews:

Related manuals for WM2000

Brands by name

Popular brands

Dane Technologies WM2000, Owner'S Manual

Search results

Summary of Contents for WM2000

Reviews:

Related manuals for WM2000

Brands by name

Popular brands