background image

Triple ON-AIR Input Stereo Module 

AirMax from D&R - Phone: +31 294 418014 - E-Mail: 

[email protected]

 

- 7 - 

4  TRIPLE ON-AIR Input Stereo Module 

 
 

MIC INSERT

 

The MIC INSERT led indicates whether a balanced insert is switched in or out of the signal  
microphone’s signal path. 
 

TRIM 

The TRIM control ads an extra 30dB of gain to the MIC pre-amp.  
An optimal gain range setting can be accomplished in this way. 
 

GAIN 

The GAIN control adjusts the incoming signal level on the MIC and LINE input. 
 

INPUT 

The INPUT switch allows the user to switch input between MIC, LINE A and LINE B.  
The associated LEDS indicate which input is currently selected. 
 

MONO 

The MONO led indicates if the stereo input signal of this module is switched to summed mono 
output signals. 
 

PROG 

The PROG(ram) switch assigns the signal in stereo to the PROG(ram) output. 
 

SUB 

The SUB switch assigns the signal in stereo to the SUB output. 
 

AUX1 

The AUX1 control adjusts the amount of signal send to the stereo AUX 1 bus. 
 

AUX2 

The AUX2 control adjusts the amount of signal send to the stereo AUX 2 bus. 
 

PAN 

Allows adjustment between the left and right channel outputs. 
 

COMM 

The COMM switch enables communication between this channel and anyone who has access 
to the COMM bus at the same time. 
 

CUE/SEL 

Stereo pre-fade listening allows for pre-fade listening of the channel with the fader closed.  
In configuration mode this switch is used to program the modules identity. 
 

PK 

The PK led acts as a peak led on the input signal. 
 

FADER 

The linear FADER controls a VCA and thereby the module's overall level. 
 

ON 

Channel ON/OFF switch. the associated LED will light when the ON switch is activated. 
 

RIAA Plug-in PCB 

Optionally a RIAA Plug-in PCB can be inserted into the signal path of LINE B to connect a 
gramophone player directly to this input. 

Summary of Contents for AIRMAX





















Reviews: