manualshive.com logo in svg

d&b audiotechnik ArraySight, Manual

Share
Download
d&b audiotechnik ArraySight Manual Download Page 22

 

8.1  EU declaration of conformity (CE symbol)
This declaration applies to:

d&b Z5710 ArraySight set
Including:
▪ Z5711 ArraySight sender unit

▪ Z5712 ArraySight meter unit
Provided they correspond to the original technical version and

have not been subject to any later design or electro mechanical

modifications.
▪ General Product Safety Directive 2001/95/EC

▪ IEC 61010-1:2010 (3

rd

 Edition) Safety requirements for

electrical measurement, control and laboratory use.

▪ IEC/EN 60825-1:2014 Safety of laser products.
▪ IEC 60529/A2:2013 Degrees of protection provided by

enclosure (IP code).

▪ Electromagnetic Compatibility (EMC) Directive) 2014/30/EU

▪ EN61326-2-1:2013 (EN 61326-1:2013) & FCC CFR 47

parts 15, 107 & 15.109 and ICES-003 Issue 6 (EMC).

▪ Restriction of Hazardous Substances 2011/65/EU
We herewith declare that said products are in conformity with the

provisions of the respective EC directives and Standards including

all applicable amendments.

8.2  WEEE Declaration (Disposal)
Electrical and electronic equipment must be disposed of separately

from normal waste at the end of its operational lifetime.
Please dispose of this product according to the respective national

regulations or contractual agreements. If there are any further

questions concerning the disposal of this product, please contact

d&b audiotechnik.

8  Manufacturer's declarations

 

d&b ArraySight Manual 1.7 en

22

Summary of Contents for ArraySight





























Reviews:

No comments

Brands by name

Popular brands

Load more brands