manualshive.com logo in svg

DANA SPICER TM4 SUMO HP HV Powertrain, Troubleshooting Manual

Share
Download
DANA SPICER TM4 SUMO HP HV Powertrain Troubleshooting Manual Download Page 80

 

 

 

80 

Service Codes 

Is the MCU Part Number

 from your note corresponding to 

the one  found under the DANA

 TM4 extranet folders ?

Complete

Does the same

SysFile ID occur

again?

No

Contact Dana 

TM4.

Yes

Yes

No

Access to your system and open 

all MCU, MOTOR and 

SOFTWARE subfolders under 

your system.

Make sure to use the proper 

MCU part number that is 

compatible with your system. 

Is the motor Part Number

 from your note corresponding to 

the one found under the DANA 

TM4 extranet folders ?

Yes

No

Make sure to use the proper 

motor part number that is 

compatible with your system. 

Is the MCU software

 version on your note matching 

corresponding to the one found 

under the DANA TM4 extranet 

folders ? 

Yes

Download the official software 

version from the extranet site and 

execute the file on the PC where 

ODIN is installed.

No

Click the server icon located just 

below the 

   

File

   

ODIN menu 

twice ( once to disconnect and 

twice to reconnect).

Turn ignition OFF.

Start the flashing process by 

selecting the software version 

you just downloaded located in 

the flashing drop down menu and 

select 

   

Start

   

Turn ignition ON. Wait until 

the flashing process is 

complete.

A

Connect to the MCU with 

ODIN tool and check the 

SysFile.

Summary of Contents for SPICER TM4 SUMO HP HV Powertrain

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands