manualshive.com logo in svg

DANA SPICER TM4 SUMO HP HV Powertrain, Troubleshooting Manual

Share
Download
DANA SPICER TM4 SUMO HP HV Powertrain Troubleshooting Manual Download Page 134

 

 

 

134 

Service Codes 

 

Troubleshooting Tree 32

Are there other systems

connected on the same MCU DC side 

that reports or could have a sudden 

loss of insulation ?

Yes

Investigate / correct the issue 

with the other system.

Note the software version on 

the status bar.

Turn ignition ON.

Connect to the MCU with 

ODIN.

Check the compatibility of the 

software flashed to the MCU with the 

one published on the Dana TM4 

extranet site for your system.

Access to your system and 

open all MCU, MOTOR and 

SOFTWARE subfolders under 

your system.

No

Is the software package

 flashed to the MCU is the up to 

date software as published on the 

Dana TM4 extranet site for your 

system ?

Download and execute the 

software package from the Dana 

TM4 extranet site.

Turn ignition OFF.

Flash the up to date software 

package to the MCU.

Refer to the Appendix section 

 

Update Software

 

 

Turn ignition ON.

No

Perform a road test to check 

further occurrences of the 

original SysFile ID.

Does the same

SysFile ID occur

again?

Complete

No

Wait for 10 minutes before 

taking any further action.

Yes

Yes

Connect to the MCU 

with ODIN to check the 

SysFile.

Ensure all High Voltage 

Electrical sources are 

switched OFF.

Switch OFF the auxiliary 

batteries switch.

A

Summary of Contents for SPICER TM4 SUMO HP HV Powertrain

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands