manualshive.com logo in svg

DANA SPICER TM4 SUMO HP HV Powertrain, Troubleshooting Manual

Share
Download
DANA SPICER TM4 SUMO HP HV Powertrain Troubleshooting Manual Download Page 166

 

 

 

166 

Service Codes 

Disconnect the harness connector from 

the concerned system (MCU or motor).

Clean  connector pins (male, 

female or both) with isopropyl 

alcohol using a brush.

Complete

Turn ignition ON.

Is there any 

evidence of a foreign

 material in one of the connectors, a 

product pin surface damaged, evidence 

of dirt or too much protective grease? 

(Inspect both male and female 

connectors.)

Reconnect the 

harness connector 

to the product 

(MCU or motor).

Does the same SysFile ID 

occur again?

Turn ignition ON.

Remove any foreign material 

from the connector.

Complete

Disconnect the harness 

connector from the 

system (MCU or motor).

Yes

Is there any evidence

of any damaged pins in the 

harness  connector(s) ?

Defective product.

Replace product.

Is one of 

the pins on the 

system connector 

bent ?

Using a plier, 

gently try to 

straighten the 

bent pin.

Yes

Is one of the pins

 on the system 

connector broken ?

A

A

No

B

B

Is there

 any evidence of 

a continuity 

loss ?

Using a multimeter, 

validate the conductivity 

between both ends of 

the harness connector 

for each pin.

No

No

Reconnect the harness 

connector to the product

(MCU or motor).

No

Does the

 same SysFile ID 

occur again?

Yes

Replace the  

harness 

connector.

Does the same SysFile ID 

occur again?

Complete

No

Yes

Is one of the 

product connector

 pins not attached properly 

and tends to move towards 

the inside of

 the product ?

Using a plier, gently try to 

pull on the pin until the 

locking mechanism of the 

pin is engaged.

Can the

 locking mechanism 

be activated ?

Yes

Complete

B

Yes

Is the product 

signal connector

an Amphenol Type 

connector ?

Amphenol type connector

No

No

Does the 

whole connector moves 

towards the inside of the 

system while pushing firmly 

on the base of the  

connector?

Yes

Yes

Yes

No

STT01

No

No

Connect to the MCU 

with ODIN to check the 

SysFile.

Connect to the MCU 

with ODIN to check the 

SysFile.

Make sure the auxiliary batteries 

switch is switched OFF.

Switch ON the auxiliary 

batteries switch.

Switch ON the 

auxiliary batteries 

switch.

Yes

No

Refer to the Dana TM4 Product installation 

guide for more details on product 

connector pinout information

Yes

Yes

No

C

C

Summary of Contents for SPICER TM4 SUMO HP HV Powertrain

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands