damian SNACK EUROPA Installation And Service Download

Page: 39 / 43

Serie "EUR7"

Pagina A - 21

Rev. M - 01

UMMARY TABLE

(*) Memorandum to be filled out after the programming under way

Menu

Parameter

Meaning

Min-Max

Default

Adjusted

to (*)

General Param’s

Language

Message language

Italian

General Param’s

LCD contrast

LCD contrast setting

General Param’s

Operating mode

MDB

General Param’s

DDD DD/mm hh:mm

Clock setting

General Param’s

DateTime Dsp
Enable

Clock enable

Enabled -
Disabled

Enabled

General Param’s

SaveMode delay

Activation delay in SaveMode

0 ÷ 120 minutes

General Param’s

Light in SaveMode

Light intensity in SaveMode

0 ÷ 100%

100%

General Param’s

NightMode
timetable

NightMode Activation
Timetable

19:00÷7.00

General Param’s

NightMode Light

Light intensity in NightMode

0 ÷ 100%

100%

General Param’s

NightMode temp.

Temperature setting in
NightMode

0 ÷ 50 °C

General

Param’s

Refrigerator
operation

Refrigerator Operation

Aut.

General Param’s

FTCA enabling

Vending sensor enabling

0)Disabled,
1)Enable Nostep,
2)3step

3step

General Param’s

FTCA max 3 sel.

FTCA max 3 selections

Enabled -
Disabled

Enabled

General Param’s

Decimal point

Decimal point position

0 ÷ 3

General Param’s

Code Mode

Internal code software

Read only

General Param’s

Software versions

Displays software versions

General Param’s

Default P. Reset

Card reinitialisation

Password required

General Param’s

Protected param.

Protected parameters

Password required

Reset Temp.

---

Reinitialise overtemperature times

Price management Price-A N.:xx

Value of each of the 44
associable „A‟ bracket prices

0 ÷ 635.35

2.00

----

Price management Price-B enabling

Enabling „B‟ price bracket

Enabled -
Disabled

Disabled

Price management Price-B N.:xx

Value of each of the 44
associable „B‟ bracket prices

0 ÷ 635.35

2.00

----

Price management Enabl. Dir. Sel.

Enabling direct selections

0)OFF Disable,

1)ON Manualreset,
2)ON Auto Reset

Disabled

Price management Drawer L-C

Direct selection association

S1-S2-S3

Price management Drawer L-C

Price associated with drawer
(Line)

, (column)

0 ÷ 44

----

Price management Enable Price Dsp

Display of the selling price

Enabled -
Disabled

Enabled

Executive
parameters

Min. coin values

Coin scaling factor

0 ÷ 1000

000.01

MDB parameters

Maximum credit

Maximum accepted credit

0 ÷ 635.35

MDB parameters

MinTube NoChange

Minimum coins to

turn “

change

” indicator light on

MDB parameters

MinTube Change

Minimum coins for giving
change

MDB parameters

Obligatory Sale

Compulsory sale

Enabled -
Disabled

Disabled

MDB parameters

Enab. Man.
Dispens

Manual emptying of the coin
tubes

Enabled -
Disabled

Disabled

Summary of Contents for SNACK EUROPA












































Search results

Summary of Contents for SNACK EUROPA

Reviews:

Related manuals for SNACK EUROPA

Brands by name

Popular brands

damian SNACK EUROPA, Installation And Service

Search results

Summary of Contents for SNACK EUROPA

Reviews:

Related manuals for SNACK EUROPA

Brands by name

Popular brands