manualshive.com logo in svg

Daktronics VIP-5000 Series, Operation Manual, Page: 7 / 62

Share
Download
Daktronics VIP-5000 Series Operation Manual Download Page 7

– 3 –

Connecting to the Network

To connect the processor to the network, follow the steps below:
1.  Connect an RJ45 network cable to the network port on the processor. Refer to 

Figure 7

 and 

Figure 8

.

Note: 

For a display-mount system, rotate the input a quarter turn clockwise to lock  

the connector.

Figure 7: 

Display-Mount Network Input

2.  Connect the other end of the cable to a computer or Ethernet network.

Power and Sensors

Display Mount

To connect power to the processor 

in a display-mount system, follow the 

steps below:
1.  Connect the Daktronics-provided 

breakout cable to the power/

sensor port on the processor. 

Refer to 

Figure 9

 and 

Figure 10

.

2.  Twist the connector to secure it 

properly.

3.  Connect the power cord to the 

breakout cable.

4.  Terminate the cord at the display’s power panel.
To enable temperature and light sensors on a display-mount 

processor, follow the steps below:
1.  Connect a breakout cable to the power/sensor port on the 

processor. Refer to 

Figure 9

 and 

Figure 10

.

2.  Twist the connector to secure it properly.
3.  Connect the Daktronics-supplied sensor cable to the breakout cable.

Figure 8: 

Rack-Mount Network Input

Figure 9: 

Display-Mount 

Power Input

Figure 10: 

Display-Mount 

Power & Sensor  

Breakout Panel

Summary of Contents for VIP-5000 Series































































Reviews:

No comments