manualshive.com logo in svg

Daktronics VIP-5000 Series, Operation Manual, Page: 54 / 62

Share
Download
Daktronics VIP-5000 Series Operation Manual Download Page 54

VIP-5000 Series Quick Guide

22 February 2017
DD2773153
Rev 05

201 Daktronics Drive Brookings SD 57006

800.325.8766

www.daktronics.com/support

Page 2 of 6

Connecting to the Network

1.  Connect one end of the RJ45 network cable to the 

network port. Refer to 

Figure 6

 and 

Figure 7

.

Note: 

For a display-mount system, rotate the 

connector 

1

/

4

 turn clockwise to lock.

2.  Connect the other end of the cable to the 

computer or network.

Connecting Power

Display-Mount Systems (12VDC)

1.  Connect the breakout cable to the power/sensor 

port. Refer to 

Figure 8

.

2.  Rotate the connector 

1

/

4

 turn clockwise to lock.

3.  Connect the breakout cable to the power cord.
4.  Terminate the cord at the display’s power panel.

Rack-Mount Systems (120/240VAC)

1.  Connect the power cord to the power jack. Refer 

to 

Figure 9

.

2.  Plug the other end of the cord into an outlet.

Connecting Temperature/Light Sensors

Display-Mount Systems

1.  Connect the sensor cable’s M12 connector to the  

temperature/light port. Refer to 

Figure 10

.

2.  Turn the connector ring clockwise until tightened.

Rack-Mount Systems

Connect the sensor cable to the CAN port. Refer 

 

to 

Figure 11

.

Computer-to-Processor Setup

Connecting to the Processor

1.  Download the DisplayFind application from either the control software CD or the internet.

a.  Navigate to 

dakfiles.daktronics.com

.

b.  Click 

venus1500>Utils>DisplayFind>DisplayFind.exe

.

c.  Click 

Run

 to download the program or 

Save

 to save the file for later use.

Figure 6: 

Display-Mount 

Network Port

Figure 7: 

Rack-Mount 

Network Port

Figure 8: 

Display-Mount 

Power/Sensor Port

Figure 9: 

Rack-Mount 

Power Jack

Figure 10: 

Display-Mount 

Sensor Port

Figure 11: 

Rack-Mount 

Sensor Port

Summary of Contents for VIP-5000 Series































































Reviews:

No comments