Daktronics BA-1018 Display Manual Download Page 67 | Manualshive

Page: 67 / 216

background image

9-2 TNMC

Maintenance

9.2 Maintenance and Troubleshooting Overview

Standard Daktronics outdoor LED scoreboards typically are front-accessible, but
some models may be ordered with rear service access. For that reason, Daktronics
team name message centers have been designed so that they may be accessed from
both the front

and

rear for easy maintenance and repair of internal components.

This section provides the following TNMC information:

Signal routing summary:

provides a basic explanation of signal travel

through the TNMC display.

Power routing summary:

provides a basic explanation of power travel

through the display.

Service and diagnostics:

provides instructions for removing various

display components and explains the functions of circuit board connectors
as well as the meanings of diagnostic LEDs.

Maintenance:

lists a number of steps to take to keep the team name

message centers in safe, working order.

Troubleshooting:

lists possible display malfunctions and suggests a

number of causes and corrections for each malfunction.

Replacement parts list:

includes the part description and number of

display components that may have to be replaced during the life of this
display.

9.3 Signal

Summary

Reference Drawings:

Schematic, Red LED TNMC, Gen III...........................

Drawing A-187661

Schematic; Amber LED TNMC, Gen III.......................

Drawing A-187662

Component Locations; 832/842

Red/Amb TNMC, G-3............................................

Drawing A-187987

Use these reference drawings after 11/29/05

Schematic, Amber TNMC, Gen IV ..............................

Drawing A-252645

Schematic, Red TNMC, Gen IV ..................................

Drawing A-252681

Component Locations; 832/848

Red/Amb Led TNMC, G-4.....................................

Drawing A-257029

Refer to your schematic,

A-187661

or

A-187662 (or A-252645 or A-252681 for

GEN 4)

, for complete information on TNMC signal routing.

Drawing A-187987 (or

A-257029 for GEN 4)

indicates the locations of the internal electronic components.

From signal input from the All Sport controller, routing can be summarized as
follows:

1.

Data from the display controller travels via cable harness into the

scoreboard.

«
...
65
66
67
68
69
...
»

Summary of Contents for BA-1018

























































































































































































































Reviews:

No comments

Related manuals for BA-1018

Brand: Waycon Pages: 8

Brand: Daikin Pages: 6

Brand: C&D Technologies Pages: 5

Brand: Uclear Pages: 2

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 2

Brand: Oki Pages: 4

Brand: Omnicomm Pages: 20

Brand: omnicharge Pages: 12

Brand: RADEMACHER Pages: 48

Brand: Z-Wave Pages: 10

Instrument Control System

Brand: Opus-Two Pages: 8

Brand: BabyOno Pages: 24

Brand: Honda Pages: 6

Brand: PROAIM Pages: 4

Brand: Logik Pages: 52

Brand: Rola Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands