Daktronics BA-1018 Display Manual Download Page 57

Page: 57 / 216

8-4

Scoreboard

Maintenance

Disconnect all connectors from the driver. Release each connector by
squeezing together the locking tabs as you pull the connector free.

Note:

When reconnecting, remember that these are keyed connectors and

will attach in one way only. Do not attempt to force the connections.

Remove the screws, nuts, or wing nuts securing the driver to the inside of
the enclosure.

Carefully lift the driver from the display and place it on a clean, flat surface.

Follow steps 1 through 5 in reverse order to attach a new driver.

8.3 Schematic

Reference Drawings:

Schematic, Multipurpose LED Driver ..........................

Drawing A-165028

Schematic; Gen III Outdoor LED, 16 Column Drvr .....

Drawing A-177931

Schematic, Gen III Outdoor Driver, 8 Column Driver ..

Drawing A-177935

Schematic; Gen III OD LED, 3 Drvr Display................

Drawing A-179541

Schematic; Gen III, OD LED, 1 Drv w/TNMC..............

Drawing A-179790

Schematic; Gen III, OD LED, 3 Drv w/TNMC..............

Drawing A-180081

Schematic; Gen III, O.D. LED, 2 Drvr Display.............

Drawing A-180637

Harness Assemby Diagram; 60” Digit .........................

Drawing A-232925

Schematic; 60” LED Clock ..........................................

Drawing A-273885

Schematic; BA-2011/2007 Gen III...............................

Drawing B-181354

Schematic, GEN III OD LED, 1 DRVR w/ S.O.P. ........

Drawing B-210454

Drawings A-177935

A-177931

A-179790

A-179541

A-180081

A-180637

B-181354

, and

B-210454

are the schematic diagrams for the 8- and 16-column

drivers used in Daktronics outdoor single-section scoreboards. The schematics
include power and signal inputs and all wiring for the models described in this
manual. Refer to

Section 5

for a complete listing of scoreboards, their drivers and

the appropriate schematic.

8.4 LED

Drivers

Reference Drawings:

Address Table, 1 Through 128....................................

Drawing A-115078

16 Column LED Driver II Specifications ......................

Drawing A-134371

8 Column LED Driver II Specifications ........................

Drawing A-134372

Driver; Gen III Outdoor LED, 16 Col Master ...............

Drawing A-178197

Driver Assy; Gen III Outdoor LED, 8 Col Master.........

Drawing A-178235

Summary of Contents for BA-1018

























































































































































































































Search results

Summary of Contents for BA-1018

Reviews:

Related manuals for BA-1018

Brands by name

Popular brands

Daktronics BA-1018, Display Manual

Search results

Summary of Contents for BA-1018

Reviews:

Related manuals for BA-1018

Brands by name

Popular brands