[5]
MAN #650500G
VHX Setup:
Entering the VHX setup is done by holding SW1 (I) and tur
ning the ignition to “on”, or “acc”.
Once in setup, one can move between
speed
,
tach
,
volt
,
water
, etc…. by tapping SW1 (I)
If you are setting multiple items, once done with one section you will automatically move onto the next item.
Obtaining speed from the BIM-01-2
•
Hold the SW1 (I) switch from the instrument system control box while turning the key on.
o
The message display should show
SETUP
.
•
Release SW1 (I) - LCD1 should show
SETUP SPEED
.
•
Press and hold SW1 (I) for at least 3 seconds until
SPEED SENDER
is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until
SENDER
is displayed.
•
Release the switch and
SENDER NORMAL
will be displayed.
•
Tap SW1 (I) until
SENDER BUS
is displayed.
•
Press and hold SW1 (I) until
DONE
is displayed.
o
NOTE: The
AUTO
, auto calibration, is removed.
o
Speed can only be fine-tuned with the
ADJUST
mode at a standstill.
o
ADJUST
now only alters the percentage of speed by +/- 25%.
▪
Drive a known speed and calculate how far off the speed is in percentage.
•
GPS speed / displayed speed x 100
•
Sample - [60/50=1.2] [1.2x100 = 120]
120%
▪
Enter setup and go to
ADJUST
, tap SW1 (I) to increment from 100% up to 125%.
▪
After 125% the values will fall back to 75% and increment up again.
▪
When the desired percentage is reached, hold SW1 (I) until
DONE
is displayed
•
Tap SW1 (I) until
SPEED DONE
is displayed.
•
Press and hold SW1 (I) until a big
DONE
is displayed.
Obtaining RPM from the BIM-01-2
•
Hold the SW1 (I) switch from the instrument system control box while turning the key on.
o
The message display should show
SETUP
.
•
Release SW1 (I) - LCD1 should show
SETUP SPEED
.
•
Tap SW1 (I) until
SETUP TACH
is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until
TACH ENGINE
is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until
ENGINE
is displayed.
•
Release the switch and
ENGINE 8
will be displayed.
•
Tap SW1 (I) until
ENGINE BUS
is displayed.
•
Press and hold SW1 (I) until
DONE
is displayed.
•
Tap SW1 (I) until
TACH DONE
is displayed.
•
Press and hold SW1 (I) until a big
DONE
is displayed.
Obtaining engine temperature from the BIM-01-2
•
Hold the SW1 (I) switch from the instrument system control box while turning the key on.
o
The message display should show
SETUP
.
•
Release SW1 (I) - LCD1 should show
SETUP SPEED
.
•
Tap SW1 (I) until
SETUP WATER
is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until
WATER SENDER
is displayed.
•
Press and hold SW1 (I) for at least 3 seconds until
SENDER DD F
is displayed.
•
Release the switch and
SENDER DD F
will be displayed.
•
Tap SW1 (I) until
SENDER BUS F
(Fahrenheit) is displayed.
o
Tap SW1 (I) once more for
SENDER BUS C
(Celsius) if desired.
•
Press and hold SW1 until
DONE
is displayed.
•
Tap SW1 (I) until
WATER DONE
is displayed.
•
Press and hold SW1 (I) until a big
DONE
is displayed.
Summary of Contents for BIM-01-2
Page 11: ... 11 MAN 650500G Notes ...
