[6]
MAN #650695
HDX and RTX setup:
**HDX/RTX systems can be configured with the Dakota Digital app for Apple and Android devices**
HDX and RTX Operations
•
HDX:
With the ignition key already on, press and hold both switches to enter SETUP, release when instructed.
o
If using the external rocker switch, hold SW2 (II) while turning the ignition on.
o
Release the switch when SETUP is shown.
o
Left switch on display is SW1, and right switch on display is SW2
•
RTX:
With the ignition off, press hold SW2 (II) while turning the ignition key on to enter SETUP
o
Release the switch when SETUP is shown.
•
BOTH:
When holding for an option, release the button when the screens says
“RELEASE”
•
BOTH:
You may skip to whichever reading you’d like to configure below; they do not need to be done in order.
•
BOTH:
After making a selection, tap a switch and select BACK to save and return to the main menu, then select
EXIT SETUP to return to normal operation.
•
BOTH:
SWI (left) moves up
↑
the menu list, SWII (right) moves down
↓
the menu list
Obtaining speed from the BIM-01-2-J1939
•
Tap SWII (right) switch until SPEED is selected. Press and hold SWII (right) switch to enter SPEED menu.
•
Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•
SIGNAL will be is displayed. Press and hold SWII (right) switch to enter SIGNAL menu.
•
Tap right switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•
When SIGNAL is displayed again, tap switch until BACK is displayed, then hold to return to INPUT.
•
When INPUT is displayed again, tap switch until BACK is displayed, then hold the switch to exit.
o
NOTE
: The AUTO CAL, auto calibration, is not accessible.
o
ADJUST now only alters the percentage of speed by +/- 25%.
▪
After the engine is running, enter setup and go to ADJUST.
▪
While driving a known speed, SWI and SWII (left/right) can adjust speed.
•
Percentage can also be adjusted without driving.
▪
Tap SWII (right) to increment up to 125%.
▪
Tap SW1 (left) to decrement down to 75%.
▪
The speed will be displayed in the LCD along with the percent chosen.
▪
Once the speed is correct, hold either switches until RELEASE is displayed.
▪
You may now continue to exit the setup menu.
o
The Dakota Digital Automotive app can also be used either while driving or not driving.
Obtaining RPM from the BIM-01-2-J1939
•
Tap SWII (right) switch until TACH is selected. Press and hold SWII (right) switch to enter TACH menu.
•
Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•
Tap SWII (right) switch until CYLINDER is displayed. Press and hold SWII (right) switch to select CYLINDER.
•
Tap SWI (
left
) switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•
When INPUT is displayed again, tap until BACK is displayed, then hold the switch to exit.
Obtaining engine temperature from the BIM-01-2-J1939
•
Tap SWII (right) switch until WATER is selected. Press and hold SWII (right) switch to enter WATER menu.
•
Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•
Tap SWII (right) switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•
When INPUT is displayed again, tap until BACK is displayed, then hold the switch to exit.
Obtaining oil pressure from the BIM-01-2-J1939
•
Tap SWII (right) switch until OIL is selected. Press and hold SWII (right) switch to enter OIL menu.
•
Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•
Tap SWII (right) switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•
When INPUT is displayed again, tap until BACK is displayed, then hold the switch to exit.
Obtaining fuel from the BIM-01-2-J1939
•
Tap SWII (right) switch until FUEL is selected. Press and hold SWII (right) switch to enter FUEL menu.
•
Tap SWII (right) switch until INPUT is displayed. Press and hold SWII (right) switch to enter INPUT menu.
•
Tap SWII (right) switch until BIM is displayed. Press and hold SWII (right) switch to select BIM.
•
When INPUT is displayed again, tap until BACK is displayed, then hold the switch to exit.
HDX/RTX TIP
: Intake/manifold air temp, ambient air temp, air fuel ratio, trans fluid temp, fuel pressure and boost will be
displayed in the group screens if activated through the displays>>group set menu setup.
Summary of Contents for BIM-01-2-J1939
Page 11: ... 11 MAN 650695 Notes ...
