Dakota Digital BIM-01-2-J1939 Manual Download Page 5

Page: 5 / 12

[5]

MAN #650695

VHX Setup Continued:

Obtaining oil pressure from the BIM-01-2-J1939

•

Hold the SW1 (I) switch from the instrument system control box while turning the key on.

The message display should show

SETUP

•

Release SW1 (I) - LCD1 should show

SETUP SPEED

•

Tap SW1 until

SETUP OIL

is displayed.

•

Press and hold SW1 (I) for at least 3 seconds until

OIL SENDER

is displayed.

•

Press and hold SW1 (I) for at least 3 seconds until

SENDER NORMAL

is displayed.

•

Release the switch and

SENDER NORMAL

will be displayed.

•

Tap SW1 (I) until

SENDER BUS

is displayed.

•

Press and hold SW1 (I) until

DONE

is displayed.

•

Tap SW1 (I) until

OIL DONE

is displayed.

•

Press and hold SW1 (I) until a big

DONE

is displayed.

***Intake/manifold air temp, ambient air temp, air fuel ratio, trans fluid temp, fuel pressure, oil temp and boost will be displayed in the message center if
activated through the display menu setup.

Summary of Contents for BIM-01-2-J1939













Search results

Summary of Contents for BIM-01-2-J1939

Reviews:

Related manuals for BIM-01-2-J1939

Brands by name

Popular brands

Dakota Digital BIM-01-2-J1939, Manual

Search results

Summary of Contents for BIM-01-2-J1939

Reviews:

Related manuals for BIM-01-2-J1939

Brands by name

Popular brands