background image

9

3P184443-12N

English

(3)  Install the suspension bolts.

(Use either an M8 – M10 size bolt or the 

equivalent)

Use a hole-in anchor for existing ceilings, 

and a sunken insert, sunken anchor or 

other field supplied parts for new ceilings to 

reinforce the ceiling to bear the weight of the 
unit.

Adjust clearance (2 – 4 in.) from the ceiling 

before proceeding further.

NOTE 

•  All the above parts are field supplied.

2-4

<Installation Example>

Ceiling slab

(Unit:in.)

Anchor

Long nut or turn-buckle
Suspension bolt

False ceiling

Fig. 6

5. INDOOR UNIT INSTALLATION

Installing optional accessories (except for the decoration panel) before installing the indoor unit 

is easier. For existing ceilings, install Fresh air intake kit and branch duct before installing the 

unit.

As for the parts to be used for installation work, be sure to use the provided accessories and specified 

parts designated by Daikin.
(1)  For new ceilings

(1-1)  Install the indoor unit temporarily.

•  Attach the hanger bracket to the suspension bolt. Be sure to fix it securely by using a nut and 

washer (3) from the upper and lower sides of the hanger bracket.
The washer fixing plate (7) will prevent the washer from falling.

Washer (3) (accessory)

Hanger bracket

[Securing the hanger bracket]

Tighten

(double nuts)

Nut

(Field supplied)

Insert

Washer fixing plate (7)

(accessory)

[Securing the washer]

Fig. 7

Fig. 8

(1-2) 

Refer to the paper pattern for installation (5) for ceiling opening dimension.

Consult the builder or carpenter for details.

• 

The center of the ceiling opening is indicated on the paper pattern for installation.
The center of the unit is indicated on the paper pattern for installation.

•  Fix the paper pattern to the unit with screws (6) (×4).

Summary of Contents for VRV FXZQ07MVJU9




























Reviews: