background image

7 Configuration

Installer and user reference guide

32

RXYSCQ4~6TMV1B

VRV IV-S system air conditioner

4P404224-1C – 2019.07

7.2.9

To connect the PC configurator to the
outdoor unit

X41A

2

3

4

5

H J

ST

a

b

c (X41A)

A1P

a

PC

b

Cable (EKPCCAB)

c (X41A)

Extension cable connected to X41A

A1P

Outdoor unit main PCB

7.3

Energy saving and optimum
operation

This  heat  pump  system  is  equipped  with  advanced  energy  saving
functionality.  Depending  on  the  priority,  emphasises  can  be  put  on
energy saving or comfort level. Several parameters can be selected,
resulting  in  the  optimal  balance  between  energy  consumption  and
comfort for the particular application.

Several  patterns  are  available  and  explained  below.  Modify  the
parameters  to  the  needs  of  your  building  and  to  realize  the  best
balance between energy consumption and comfort.

No  matter  which  control  is  selected,  variations  on  the  behaviour  of
the  system  are  still  possible  due  to  protection  controls  to  keep  the
unit  operating  under  reliable  conditions.  The  intentional  target,
however,  is  fixed  and  will  be  used  to  obtain  the  best  balance
between  energy  consumption  and  comfort,  depending  on  the
application type.

7.3.1

Available main operation methods

Basic

The refrigerant temperature is fixed independent from the situation. It
corresponds  to  the  standard  operation  which  is  known  and  can  be
expected from/under previous VRV systems.

To activate this in…

Change…

Cooling operation

[2‑8]=2

Heating operation

[2‑9]=2

Automatic

The refrigerant temperature is set depending on the outdoor ambient
conditions.  As  such  adjusting  the  refrigerant  temperature  to  match
the  required  load  (which  is  also  related  to  the  outdoor  ambient
conditions).

E.g., when your system is operating in cooling, you do not need as
much  cooling  under  low  outdoor  ambient  temperatures  (e.g.,  25°C)
as under high outdoor ambient temperatures (e.g., 35°C). Using this
idea,  the  system  automatically  starts  increasing  its  refrigerant
temperature,  automatically  reducing  the  delivered  capacity  and
increasing the system's efficiency.

E.g., when your system is operating in heating, you do not need as
much heating under high outdoor ambient temperatures (e.g., 15°C)
as under low outdoor ambient temperatures (e.g., –5°C). Using this
idea,  the  system  automatically  starts  decreasing  its  refrigerant
temperature,  automatically  reducing  the  delivered  capacity  and
increasing the system's efficiency.

To activate this in…

Change…

Cooling operation

[2‑8]=3 (default)

Heating operation

[2‑9]=1 (default)

Hi-sensible/economic (cooling/heating)

The  refrigerant  temperature  is  set  higher/lower  (cooling/heating)
compared to basic operation. The focus under high sensible mode is
comfort feeling for the customer.

The  selection  method  of  indoor  units  is  important  and  has  to  be
considered as the available capacity is not the same as under basic
operation.

For  details  concerning  to  Hi-sensible  applications,  please  contact
your dealer.

To activate this in…

Change…

Cooling operation

[2‑8] to the appropriate value,
matching the requirements of the
pre-designed system containing
a high sensible solution.

Heating operation

[2‑9] to the appropriate value,
matching the requirements of the
pre-designed system containing
a high sensible solution.

[2‑8]

T

e

 target (°C)

4

8

5

9

6

10

7

11

[2‑9]

T

c

 target (°C)

4

43

7.3.2

Available comfort settings

For  each  of  above  modes  a  comfort  level  can  be  selected.  The
comfort  level  is  related  to  the  timing  and  the  effort  (energy
consumption)  which  is  put  in  achieving  a  certain  room  temperature
by  temporarily  changing  the  refrigerant  temperature  to  different
values in order to achieve requested conditions more quickly.

Powerful

Overshoot  (during  heating  operation)  or  undershoot  (during  cooling
operation)  is  allowed  compared  to  the  requested  refrigerant
temperature, in order to achieve the required room temperature very
fast. The overshoot is allowed from the start up moment.

▪ In  case  of  cooling  operation  the  evaporating  temperature  is

allowed  to  go  down  to  3°C  on  temporary  base  depending  on  the
situation.

▪ In case of heating operation the condense temperature is allowed

to go up to 49°C on temporary base depending on the situation.

▪ When the request from the indoor units becomes more moderate,

the system will eventually go to the steady state condition which is
defined by the operation method above.

To activate this in…

Change…

Cooling operation

[2‑41]=3.

This setting is used in
conjunction with setting [2‑8].

Heating operation

[2‑42]=3.

This setting is used in
conjunction with setting [2‑9]

Summary of Contents for RXYSCQ6TMV1B





















































Reviews: