background image

9

English

Wiring

 WARNING

1) Do not use tapped wires, stranded wires (

CAUTION (1)

), extension cords, or starburst connections, as they may cause over-

heating, electrical shock, or fire.

2) Do not use locally purchased electrical parts inside the product. (Do not branch the power for the drain pump, etc., from the 

terminal block.) Doing so may cause electric shock or fire.

3) Be sure to install an earth leak detector. (One that can handle higher harmonics.)

(This unit uses an inverter, which means that it must be used an earth leak detector capable handling harmonics in order to 
prevent malfunctioning of the earth leak detector itself.)

4) Use an all-pole disconnection type breaker with at least 3mm between the contact point gaps.

5) The earth leakage circuit breaker must operate at 30mA or lower.

• Do not turn ON the safety breaker until all work is completed.

1) Strip the insulation from the wire (20mm).
2) Connect the connection wires between the 

indoor and outdoor units 

so that the termi-

nal numbers match.

 Tighten the terminal 

screws securely. We recommend a flathead 
screwdriver be used to tighten the screws. 
The screws are packed with the terminal 
board.

 CAUTION (1)

In case using stranded wires is unavoidable for some reason, 
make sure to install the round crimp-style terminals on the tip. 

Place the round crimp-style terminals on the wires up to the 
covered part and secure in place.

1
2
3

1 2 3

L N

Safety 
breaker 
16A

Earth leakage 
circuit breaker

Earth

When wire length exceeds 10m, 
use 2.0mm diameter wires.

H05VV

Firmly fix the wires with 
the terminal screws.

Outdoor unit

Indoor 
unit

Power supply
50Hz 220-240V

Firmly fix the wires with 
the terminal screws.

Use 2.0mm diameter wires.

1

2

3

1

2

3

Use the specified wire type 
and connect it securely.

Firmly secure wire retainer 
so wire terminations will 
not receive external stress.

Shape wires so 
that the service 
lid fit securely.

Power supply
terminal block

Stranded wire

Round crimp-style
terminal

01_EN_3P177302-2.fm  Page 9  Thursday, May 25, 2006  6:21 PM

Summary of Contents for RXR28EV1B














Reviews: