background image

English

8

Pump Down Operation

In order to protect the environment, be sure to pump down when relocating or disposing of the unit.

1) Remove the valve cap from liquid stop valve and gas stop valve.
2) Carry out forced cooling operation.
3) After five to ten minutes, close the liquid stop valve with a hexagonal wrench.
4) After two to three minutes, close the gas stop valve and stop forced cooling 

operation.

How to force cooling operation mode

Using the indoor unit operation/stop button

Press the indoor unit operation/stop button for at least five seconds. 
(Operation will start.)

• Forced cooling operation will stop automatically after around 15 minutes. 

To force a test run to stop, press the indoor unit operation/stop button.

 CAUTION

After closing the liquid stop valve, close the gas stop valve within three minutes, then stop the forced operation.

Connecting the Humidifying Hose

1.

Connecting the humidifying hose.

1) Connect the   humidifying hose to the outdoor humidifying duct. 
2) Apply a   binding band to prevent the   humidifying hose from coming off. 

2.

Connecting the cut humidifying hoses.

• When installing the cut   humidifying hoses, follow the instructions below. 

• Use not more than 2 elbows to ensure humidifying capacity.

Liquid stop valve

Valve cap

Hexagonal 
wrench

Close

Gas stop valve

C

F

C

Outdoor 
humidifying duct

Turn the binding part of 
the       binding band to 
the outdoor unit side. 
(It is easier to attach the 
stop valve cover.)

Binding part of binding band

Attach the       humidifying 
hose, making sure there 
is no gap.

Apply the       binding band 
at 10mm from the top of 
the       humidifying hose 
to prevent the hose from 
coming off.

Humidifying 
hose

C

Humidifying 
hose

C

Binding band

F

C

C

F

F

C

Apply the       binding 
band at 10mm from the 
rim of the       joint to 
prevent the       humidifying 
hose from coming off.

Insert each       humidifying 
hose to the rim of the       joint 
so that there are no gaps.

Apply the       binding band 
at 10mm from the rim of the 

elbow to prevent the 
humidifying hose from 

coming off.

Insert each       humidifying 
hose to the rim of the       elbow 
so that there are no gaps.

C

C

C

C

F

Elbow

E

F

Joint

D

D

D

E

E

01_EN_3P177302-2.fm  Page 8  Thursday, May 25, 2006  6:21 PM

Summary of Contents for RXR28EV1B














Reviews: