background image

3

English

Outdoor Unit Installation Drawings

1.

Precautions for humidifying hose installation work.

• Moisture on the outdoor unit is brought to the indoor unit together with air around the outdoor unit during humidifying 

operation. Install the outdoor unit in a clean and calm location.

• When embedding   humidifying hose: 

1) Cannot be installed to the existing embedded piping. Embedding work is separately necessary.

• The length of the   humidifying hose is marked on the hose packing material.

1) Use an extension hose (sold separately) when extending the   humidifying hose.
2) The length of the   humidifying hose needs to be set to ensure humidifying capacity. Cut off any excess hose. 

Use the remote controller to set the hose length.

• When it is difficult to install without cutting the   humidifying hose, cut the hose and join it with included   joint or   elbow 

after the installation. When doing this, bind the hose using included   binding band so that there is no air leakage. 
(Refer to 

Connecting the Humidifying Hose

 on page 8.)

• When laying the   humidifying hose inside the wall, block the ends of the   humidifying hose with tape or the like to 

prevent water or anything else from entering it until it is connected to the indoor unit and outdoor unit ducts.

• Do not bend the   humidifying hose more than 90°. 

C

C

C

C

C

D

E

F

C

C

C

Wrap the insulation pipe with 
the finishing tape from bottom 
to top.

In sites with poor drainage, use 
block bases for outdoor unit.  
Adjust foot height until the unit 
is leveled.  Otherwise, water 
leakage or pooling of water may 
occur.

574

(Foot bolt-hole centres)

(From unit’

s side)

Where there is a danger of the unit 
falling, use foot bolts, or wires.

(Foot bolt-hole 

centres)

311

250mm from w

all

Unit: mm

How to remove the stop valve cover.

Remove the screw on the 
stop valve cover.
Slide the lid downward 
to remove it.

How to attach the stop valve cover.

Insert the upper part of the 
stop valve cover into the 
outdoor unit to install.
Tighten the screws.

Stop valve cover

O.D. 9.5mm

Gas pipe

Liquid pipe

O.D. 6.4mm

8m

10m

Max. allowable length

Max. allowable height

*

 No refrigerant needs to be added if the piping does not 

exceed the maximum length. 

105.5

Humidifying hose

C

Allow space for piping 
and electrical servicing.

01_EN_3P177302-2.fm  Page 3  Thursday, May 25, 2006  6:21 PM

Summary of Contents for RXR28EV1B














Reviews: