Daikin RXQ5P7W1B, Installation Manual

Page: 29 / 38

RX(Y)Q5-10-1 RXQ RXYQ
RXYHQ1 RX(Y)Q14~18P7W1BA
VRVIII System air conditioner
4PW48461-1
Installation manual
24
3 Normal system display
4 Remote controller malfunction code display
Remote controller heating mode malfunction codes
Remote controller cooling mode malfunction codes
5 Final adjustment of the amount of refrigerant
■
When the unit displays an out of temperature range, the
automatic charging of refrigerant can not be completed.
■
Out of outdoor temperature range
Complete the charging of refrigerant on another time when
the outdoor temperature is warmer than 0°C DB and colder
than 43°C DB.
■
Out of indoor temperature range
Complete the charging of refrigerant on another time when
the indoor temperature is warmer than 20°C DB and colder
than 32°C DB.
In this case, perform a test operation (as explained in the
chapter
"12.4. Test operation" on page 27 ) and the unit will work
properly. (The malfunction code
U3
will be displayed on the
indoor unit.)
However, the refrigerant leak detection function can not be used
before completing the refrigerant charging operation and the
judgement of the initial amount of refrigerant by performing the
test operation again.
■
When the temperature has come in range (outdoor = 0~43°C,
indoor
= 20~32°C), perform the overcharging judgement
procedure for completion of the refrigerant charging operation.
Overcharging judgement procedure
1 Close all the front panels except the electric box front panel and
the lid on the side of the electric box.
2 Turn on the power to the outdoor unit and all the connected
indoor units.
3 Press the button once and set the setting model
H1P = OFF.
4 Press and hold the button down for 5 seconds.
The system will start operating.
5 Close all the front panels.
After operating for 40 minutes, the operation will stop
automatically.
6 After the system has stopped operating, check the display on
the remote controller.
7 If
E3
,
F6
or
UF
is displayed on the remote controller as a result of
the overcharge judging operation, recover 20% of the charged
amount of refrigerant and perform the overcharge judgement
procedure again.
■
When there is no more overcharging of refrigerant detected,
restart the automatic refrigerant charging from
"1. Start of
automatic charging refrigerant" as explained on page 21 again.
11.6. Checks after adding refrigerant
■
Are the stop valves for both liquid and gas open?
■
Is the amount of refrigerant, that has been added, recorded?
LED
display
(Default
status
before
delivery)
Micro-
computer
operation
monitor
Mode
Ready
/Error
Cooling/Heating
changeover
Low
noise Demand Multi
Indivi-
dual
Bulk
(master)
Bulk
(slave)
HAP H1P H2P H3P H4P H5P H6P H7P H8P
Single outdoor
unit system
c x x w x x x x x
Multiple
outdoor
unit
system
Master
unit
(a)
(a) The state of the H8P (multi) LED in a multi-system shows wich unit is the master
unit ( w ), slave 1 unit ( c ) or slave 2 unit ( x ).
Only the master unit is connected to the indoor units with interunit wiring.
c x x w x x x x w
Slave
unit
1
(a)
c x x x x x x x c
Slave
unit
2
(a)
c x x x x x x x x
Error code
P8
recharge
operation
Close valve A immediately and press the TEST OPERATION
button once.
The operation will restart from the charging mode judgement
onwards.
P2
charge
hold
Close valve A immediately. Check
following items:
- Check if the gas side stop valve is
opened correctly
- Check if the valve of the refrigerant
cylinder is opened
- Check if the air inlet and outlet of the
indoor unit are not obstructed
After correcting the
abnormality, restart
the automatic
charging procedure
again.
Error code
PA
,
PH
,
PC
replace
cylinder
Close valve A and replace the empty cylinder. When renewed,
open valve A (the outdoor unit will not stop operating).
The code on the display shows the unit where a cylinder is to be
renewed:
PA
= master unit,
PH
= slave unit 1,
PC
= slave unit 2, flashing
PA
,
PH
and
PC
= all units
After recplacing the cylinder, open valve A again and continue the
work.
P8
recharge
operation
Close valve A immediately.
Restart the automatic charging procedure again.
P2
charge
hold
Close valve A immediately. Check
following items:
- Check if the gas side stop valve is
opened correctly
- Check if the valve of the refrigerant
cylinder is opened
- Check if the air inlet and outlet of the
indoor unit are not obstructed
- Check if the indoor temperature is not
lower than 20°C DB
After correcting the
abnormality, restart
the automatic
charging procedure
again.
*
abnormal
stop
Close valve A immediately. Confirm the
malfunction code by the remote controller
and correct the abnormality by following
the
"Correcting after abnormal completion
of the test operation" on page 29 .
H1P H2P H3P H4P H5P H6P H7P
w c c c w x x
H1P H2P H3P H4P H5P H6P H7P
w c c c x w x
Make sure to open the stop valves after charging the
refrigerant.
Operating with the stop valves closed will damage the
compressor.
BS1 MODE
BS4 TEST