background image

5

English

Installation Space Requirements

•  Position the unit on a horizontal surface.  

Any tilt in the unit should be 3° or less to the horizontal.

• 

Where a wall or other obstacle is in the path of the outdoor unit’s intake or exhaust airflow, follow the installation space 

requirements below.

•  For any of the below installation patterns, the wall height on the outlet side should be 47-1/4 inch (1200mm) or less.

More than

3-15/16 (100)

More than

13-3/4 (350)

Walls facing three sides

More than 3-15/16 (100)

More than 13-3/4 (350)

More than 

1-15/16 (50)

Wall facing one side

More than 

3-15/16 (100)

More than

13-3/4 (350)

Side view

47-1/4

(1200)

or less

Top view

More than 

1-15/16 (50)

More 

than 

3-15/16 

(100)

Walls facing two sides

More than 

1-15/16 (50)

More than 

13-3/4 

(350)

Top view

unit: inch (mm)

When installed as in the figure on the left, it is recommended to either 

change the orientation of the outdoor unit outlet side or use the air direction 
adjustment grille (sold separately).

Outdoor Unit Installation

1. 

Installing the outdoor unit

•  When installing the outdoor unit, refer to “

Precautions for Selecting a Location

” and the “

Outdoor Unit Installation 

Diagram

”.

•  If drain work is necessary, follow the procedures in “

2. Drain work

”.

2. 

Drain work

CAUTION

•  In cold areas, do not use a drain socket, drain caps (1,2) and a drain hose with the outdoor unit. (Drain water may freeze, 

impairing heating performance.)

• 

If the drain port is covered by a mounting base or floor 

surface, place additional foot bases of at least 1-1/4 
inch (30mm) in height under the outdoor unit’s feet.

1) Attach 

C

 drain cap (1) and 

D

 drain cap (2).

2) Attach 

B

 drain socket.

•  When attaching 

B

 drain socket to the bottom 

frame, make sure to connect the drain hose to the 

drain socket first.

Bottom frame

Drain cap

Pinch the bottom 
frame in.

Drain cap (1)

Drain cap (2)

D

Drain cap (2)

Air outlet side

B

Drain 
socket

C

D

Bottom frame

 Drain socket

Hose (available commercially,
inner dia. 5/8 ” (16mm))

B

01_EN_3P572321-4B.indd   5

2019/10/17   14:46:58

Summary of Contents for RXL18UMVJUA















Reviews: