background image

6 Installation

Installer and user reference guide

34

RWEYQ8~1 RWEYQ8~14T9Y1B
VRV IV water-cooled system air conditioner

4P452191-1 – 2017.04

b

a

f

c

d

f

e

f

a

Liquid pipe

b

Gas pipe

c

Finishing tape

d

High pressure/low pressure gas pipe

e

Transmission wiring (F1/F2)

f

Insulator

6.9.7

To route and fix the power supply

NOTICE

When  routing  earth  wires,  secure  clearance  of  25  mm  or
more away from compressor lead wires. Failure to observe
this  instruction  properly  may  adversely  affect  correct
operation of other units connected to the same earth.

The power supply wiring can be routed from the front side. Exit the
wiring via the upper mounting hole.

A1P

6.9.8

To connect the power supply

NOTICE

Never  connect  the  power  supply  to  transmission  wiring
terminal  block.  Otherwise  the  entire  system  may  break
down.

CAUTION

When  connecting  the  power  supply,  the  earth  connection
must be made before the current-carrying connections are
established.  When  disconnecting  the  power  supply,  the
current-carrying connections must be separated before the
earth connection is. The length of the conductors between
the  power  supply  stress  relief  and  the  terminal  block  itself
must  be  as  such  that  the  current-carrying  wires  are
tautened before the earth wire is in case the power supply
is pulled loose from the stress relief.

Tightening torque for the terminal screws:

Screw size

Tightening torque (N•m)

M8 (power terminal block)

5.5~7.3

M8 (ground)

NOTICE

Recommendations when connecting the earth wire:

Wire  it  so  that  it  comes  through  the  cut  out  section  of  the
cup washer. (An improper earth connection may prevent a
good earthing from being achieved.)

The power supply must be clamped to the plastic bracket using field
supplied clamp material.

The  green  and  yellow  striped  wire  must  be  used  for  earthing  only
(refer to the figure below).

e

i

f

b

a

c

d

h

e

g

a

Power supply (380~415 V - 3N~ 50 Hz 

OR

 400 V -

3N~ 60 Hz)

b

Fuse

c

Earth leakage protector

d

Earth wire

e

Power supply terminal block

f

Connect each power wire: RED to L1, WHT to L2, BLK to
L3 and BLU to N

g

Earth wire (GRN/YLW). When connecting the earth wire, it
is recommended to perform curling.

h

Clamp the power supply to the bracket using a field
supplied clamp to prevent external force being applied to
the terminal.

i

Cup washer.

Multiple outdoor units

To connect the power supply for multiple outdoor units to each other,
ring tongues have to be used. No bare cable can be used.

In  that  case,  the  ring  washer  that  is  installed  by  default  should  be
removed.

Attach both cables to the power supply terminal as indicated below:

L1 L2 L2 N

6.9.9

To connect the optional wiring

For  the  optional  wiring  use  insulated  wires  of  a  rated  voltage  of
250 V or higher and a minimal cross section of 1.25 mm² for single
core wires and 0.75 mm² for multicore wires.

Variable water flow

The variable water flow output signal is a low voltage control signal
which generates an output of 2~10 V DC depending on the required
water  flow  rate  through  the  plate  heat  exchanger.  For  more
information, see 

"5.4.4 About the water flow rate" on page 20

.

NOTICE

The  maximum  output  power  of  the  2~10  V  DC  output
signal  is  50  mW.  Exceeding  this  power  can  result  in
damage of the system.

Always use shielded cables with a minimal cross section of
0.75 mm² and a length limited to 100 m.

Summary of Contents for RWEYQ8T9Y1B

























































Reviews: