background image

Installation and operation manual

3

Selecting installation site

1

Select an installation site where the following conditions are
fulfilled and that meets your customer's approval.
- The installation location is frost-free.
- Where optimum air distribution can be ensured.
- Where nothing blocks air passage.
- Where condensate water can be properly drained.
- Where the floor or wall is strong enough to bear the indoor 

unit weight.

- Where sufficient clearance for maintenance and service can 

be ensured.

- Where piping between indoor and outdoor units is possible 

within the allowable limit. (Refer to the installation manual of 
the outdoor unit.)

- This is a class A product. In a domestic environment this 

product may cause radio interference in which case the user 
may be required to take adequate measures.

- Keep indoor unit, outdoor unit, power supply wiring and 

transmission wiring at least 1 meter away from televisions 
and radios. This is to prevent image interference and noise in 
those electrical appliances. (Noise may be generated 
depending on the conditions under which the electric wave is 
generated, even if 1 meter is kept.)

- When installing the wireless remote controller kit, the 

communication distance between wireless remote controller 
and indoor unit might be shorter if there are fluorescent lights 
who are electrically started in the room. The indoor unit must 
be installed as far as possible away from fluorescent lights.

- Do not place objects that are susceptible to moisture directly 

beneath the indoor or outdoor units. Under certain conditions, 

2

Install the unit according to the figures below.
Unit of measurement = mm

For 

FXLQ

 units only

note

(b)

200 mm in case of wall mounting

A

Front side

B

Air inlet direction

C

Air outlet direction

(a)

(a) The air outlet direction can be chosen by rotating the discharge grille.

NOTE

Make sure no short circuit of air is caused when
placing the unit directly under a windowsill.

100

100

1000

20

A

B

C

C

A

1750

B

<1750

C

B

(b)

20

>20

C

A

A

B

C

B

01_4PEN323720-1E.book  Page 3  Tuesday, October 3, 2017  4:34 PM

Summary of Contents for FXLQ20P5VEB

















Reviews: