background image

4

English

Indoor Unit Installation Drawings

■ 

 

■ 

■ 

 

Screws
(M4 × 16L)

Service lid

Caulk pipe 
hole gap 
with putty. 

Wrap the insulation pipe 
with the finishing tape 
from bottom to top.

Cut thermal insulation 
pipe to an appropriate 
length and wrap it with 
tape, making sure that no 
gap is left in the insulation 
pipe’s cut line.

Bottom frame

Front grille

How to attach the indoor unit

Hook the claws of the bottom frame 
to the mounting plate.
If the claws are difficult to hook, 
remove the front grille.

How to remove the indoor unit

Push up the lower part of the front 
grille to release the claws. 
If they are difficult to release, 
remove the front grille.

Opening the service lid

The service lid is removable.

1) Remove the service lid screw.
2) Pull out the service lid diagonally 
down in the direction of the arrow.
3) Pull down.

The mounting plate 
should be installed on a 
wall which can support the 
weight of the indoor unit.

30mm or more from ceiling

Front panel

50mm or more 
from walls 
(on both sides)

Air filters

Mounting plate

Mounting 
plate

Mounting plate 
fixing screw 
(field supply: M4 × 25L)

Wireless remote controller

Fixing screw for remote 
controller holder 
(field supply: M3 × 20L)

Remote controller 
holder

Air filter

Titanium apatite 
photocatalytic 
air-purifying filter

Filter frame

Tab

Titanium apatite photocatalytic 
air-purifying filter (2 pcs)

Before screwing the 
remote controller holder 
to the wall, make sure 
that control signals are 
properly received by 
indoor unit.

Claw

Opening method

3PEN387973-3D.book  Page 4  Monday, November 30, 2015  4:18 PM

Summary of Contents for FTXM-K

















Reviews: