![background image](http://html1.mh-extra.com/html/daikin/ewaq005acv3p/ewaq005acv3p_installation-manual_4144383014.webp)
Installation manual
12
EWAQ+EWYQ005~007ACV3P
Packaged air-cooled water chillers and
packaged reversible air to water heat pumps
4PW33165-1D
Field settings
The unit should be configured by the installer to match the installation
environment (outdoor climate, etc.) and user expertise. Thereto, a
number of so called field settings are available. These field settings
are accessible and programmable through the digital controller.
Each field setting is assigned a 3-digit number or code, for example
[1-02], which is indicated on the digital controller display. The first
digit [1] indicates the ‘first code’ or field setting group. The second
and third digit [02] together indicate the ‘second code’.
A list of all field settings and default values is given under
. In this same list, we have provided 2
columns to register the date and value of altered field settings at
variance with the default value.
A detailed description of each field setting is given under
Procedure
To change one or more field settings, proceed as follows.
1
Press the
z
button for a minimum of 5 seconds to enter FIELD
SET MODE.
The
$
icon (3) will be displayed. The current selected field
setting code is indicated
;
(2), with the set value displayed to
the right
:
(1).
2
Press the
bgi
button to select the appropriate field
setting first code.
3
Press the
bgj
button to select the appropriate field
setting second code.
4
Press the
pfi
button and
pfj
button to change
the set value of the select field setting.
5
Save the new value by pressing the
pr
button.
6
Repeat step 2 through 4 to change other field settings as
required.
7
When finished, press the
z
button to exit FIELD SET MODE.
Detailed description
[0] User permission level
If required, the digital controller functions available to the user can be
limited by restricting the number of operable buttons. This may
prevent the user from disrupting correct operation of the installation.
Three permission levels are available (see the table below).
Switching between level 1 (default) and level 2/3 is done by pressing
the following 4 buttons at the same time for more than 5 seconds (in
normal mode):
s
,
ba
,
pfi
and
pfj
. Press these 4
buttons to switch to level 2/3, press again for 5 seconds to switch
back to level 1. When level 2/3 is selected, the actual permission level
— either level 2 or level 3 — is determined by the field setting [0-00].
■
[0-00] User permission level: applicable permission level
number (level 2 or level 3). See the table below.
[1] Weather dependent set point (heat pump models only)
The weather dependent set point field settings define the parameters
for the weather dependent operation of the unit. When weather
dependent operation is active, the water temperature is determined
automatically depending on the outdoor temperature: colder outdoor
temperatures will result in warmer water and vice versa. During
weather dependent operation, the user has the possibility to shift the
target water temperature up or down by a maximum of 5°C. See the
operation manual for more details on weather dependent operation.
■
[1-00] Low ambient temperature (Lo_A): low outdoor
temperature.
■
[1-01] High ambient temperature (Hi_A): high outdoor
temperature.
■
[1-02] Set point at low ambient temperature (Lo_Ti): the
target outgoing water temperature when the outdoor
temperature equals or drops below the low ambient
temperature (Lo_A).
Note that the Lo_Ti value should be higher than Hi_Ti, as for
colder outdoor temperatures (i.e. Lo_A) warmer water is
required.
NOTE
Changes made to a specific field setting are only
stored when the
pr
button is pressed. Navigating to a
new field setting code or pressing the
z
button will
discard the change made.
NOTE
■
Before shipping, the set values have been set as
shown under
"Field settings table" on page 13
■
When exiting FIELD SET MODE, “
88
” may be
displayed on the digital controller LCD while the
unit initialises itself.
2
3
1
Button
Permission level
1
2
3
On/off button
o
operable
operable
operable
Operation changeover
button
h
/
c
operable
operable
operable
Sanitary water heating
button
w
– Not available –
Sanitary temperature
adjust buttons
wbi
wbj
– Not available –
Temperature adjust
buttons
bg
i
bg
j
operable
operable
operable
Time adjust buttons
pf
i
pf
j
operable
Programming button
<
operable
Schedule timer enable/
disable button
pr
operable
operable
Quiet mode button
s
operable
Weather dependent
set point button
ba
operable
Inspection/test
operation button
z
operable