Daikin EHSH04P30A Operating Instructions Manual Download Page 11

Page: 11 / 56

Product description

Daikin Altherma EHS(X/H)
Daikin Altherma integrated solar unit
008.1420944 – 05/2014

Operating instructions

Tab. 2-1 Legend from fig. 2-2 to fig. 2-5

Solar - flow or connection for addition-

al heat source (1" IG)

Cold water flow (1" AG)

Hot water flow (1" AG)

Heating flow (1" AG)*

Heating return (1" AG)*

Circulation pump

Recommended accessories:



non-return valves (2 pcs.)

Storage tank (double walled jacket made
of polypropylene with PUR hard foam heat
insulation)

Filling and drainage connection or



Solar - Return flow connection

Mount for solar R3 controller or handle

Heat exchanger (stainless steel) for drink-
ing water heating

Heat exchanger (stainless steel) for stor-
age tank charging or heating support

Heat exchanger (stainless steel) for pres-
surised solar storage tank charging

Connection for optional electrical backup
heater (R 1½" IG)

Solar inflow layering pipe

Fill level indicator (tank water)

Optional: Electrical backup heater



(EKBUxx)

Submersible sensor sleeve for storage
tank temperature sensor t

DHW1

and t

DHW2

Unpressurised storage tank water

Solar zone

Hot water zone

Safety overflow connection

Mount for handle

Type plate

Protective cover

Solar - Return

Solar - Flow (3/4" IG)



(nur Typ Daikin Altherma EHS(X/H)B)

Solar - Return flow (3/4" IG)



(nur Typ Daikin Altherma EHS(X/H)B)

Panel heat exchanger

Liquid-side coolant connection



Daikin Altherma EHS(X/H)
...04P30A/08PxxA:



Cu Ø 6.4 mm (1/4"),



Daikin Altherma EHS(X/H)...16P50A:



Cu Ø 9.5 mm (3/8")

Connection to coolant gas line



Cu Ø 15,9 mm (5/8")

3UVB1

3-way diverter valve (internal heat genera-
tor circuit)

3UV DHW

3 way diverter valve (hot water/heating)

DS Pressure sensor
FLS (t

/ V1)

Return flow temperature and flow sensor

DHW1

, t

DHW2

Tank temperature sensor

Return temperature sensor

V1,

Feed temperature sensors

V, BH

Flow temperature sensor backup heat-
er

RoCon B1

Operating section Daikin Altherma
EHS(X/H) control unit

EKSRPS3B

Optional:

Daikin R3 solar control and

pump unit

Safety devices
Observe tightening torque!

AG Male thread
IG

Female thread

Ball cock (1" IG) is supplied with the equip-
ment

Summary of Contents for EHSH04P30A
























































Search results

Summary of Contents for EHSH04P30A

Reviews:

Related manuals for EHSH04P30A

Brands by name

Popular brands

Daikin EHSH04P30A, Operating Instructions Manual

Search results

Summary of Contents for EHSH04P30A

Reviews:

Related manuals for EHSH04P30A

Brands by name

Popular brands