background image

2

www.daikincomfort.com

SS-DM96SN-U

SS-DM96SN-U

www.daikincomfort.com

3

DM96SN

 

0403BU

DM96SN

 

0603BU

DM96SN

 

0805CU

Heating Data

High Fire Input¹

40,000

60,000

80,000

High Fire Output¹

38,400

57,600

76,800

AFUE²

96

96

96

Temperature Rise Range (°F)

15 - 45

30 - 60

30 - 60

Vent Diameter³

2" - 3"

2" - 3"

2" - 3"

No. of Burner Ports

2

3

4

Circulator Blower

Available AC @ 0.5" ESP

1.5 - 3

1.5 - 3

2 - 5

Size  (D x W)

10" x  8"

11" x  8"

11" x 10"

Horsepower @ 1075 RPM

 1/2

 1/2

1

No. of Speeds

9

9

9

Filter Size (in²) (Qty)

(1) 16 X 25

 

(side or bottom)

(1) 16 X 25

 

(side or bottom)

(1) 20 X 25 (bottom) 

 

(2) 16 X 25 (side)

Electrical Data

Min. Circuit Ampacity⁴

10.8

10.8

16.1

Max. Overcurrent Device (amps)⁵

15

15

20

Shipping Weight (lbs)

115

120

145

1

  Natural Gas BTU/h

DOE AFUE based upon Isolated Combustion System (ICS)

3

  Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required). Vent pipe must be either 2" or 3"

 

 in diameter, depending upon furnace input, number of elbows, length of run and installation (1 or 2 pipes). The optional Combustion Air Pipe is 

 

dependent on installation/code requirements and must be 2" or 3" diameter PVC.

4

  Minimum Circuit Ampacity = (1.25 x Circulator Blower Amps) + ID Blower amps. Wire size should be determined in accordance 

 

with National Electrical Codes. Extensive wire runs will require larger wire sizes.

5

  Maximum Overcurrent Protection Device refers to maximum recommended fuse or circuit breaker size. May use fuses or HACR-type 

 

circuit breakers of the same size as noted.

Notes

• 

All furnaces are manufactured for use on 115 VAC, 60 Hz, single-phase electrical supply.

• 

Gas Service Connection ½" FNPT

• 

Important: Size fuses and wires properly and make electrical connections in accordance with the National Electrical Code and/or all 

 

existing local codes.

• 

For bottom return: Failure to unfold flanges may reduce airflow by up to 18%. This could result in performance and noise issues.

• 

For servicing or cleaning, a 24" front clearance is required. Unit connections (electrical, flue and drain) may necessitate greater clearances 

 

than the minimum clearances listed above. In all cases, accessibility clearance must take precedence over clearances from the enclosure 

 

where accessibility clearances are greater.

Product Specifications

Summary of Contents for DM96SN









Reviews: