background image

English 

4.  PREPARATIONS BEFORE INSTALLATION

Install suspension bolts and hanging brackets as illustrated in the diagram below.

• 

Use a suspension bolt size of M8 to M10.

• 

Use mold-in inserts and embedded foundation bolts for new installations or hole-in anchor bolts or similar 
hardware for existing installations, taking care to install in a manner that can withstand the unit’s weight.

Unit: mm

BS unit

A

BS4Q14AV1

415

BS6Q14AV1

625

BS8Q14AV1

BS10Q14AV1

865

BS12Q14AV1
BS16Q14AV1

1105

A

308

<Suspension bolt spacing>

• 

Use the hanging brackets to support the connection pipes on both the front and back of the unit within  
1 m of the unit’s side. 
Placing an excessive amount of weight on the BS unit’s hanging brackets may cause the unit to fall, 
resulting in bodily injury.

Slab

Anchor bolt

Long nut or 
turnbuckle

Suspension bolt

Within 1 m

Unit

Connection 
pipe

All the above parts must be supplied in the field

<Example installation>

5.  BS UNIT INSTALLATION

Use only accessories and parts that conform to the designated specifications when installing the unit.

1.  Position the BS unit and secure it temporarily in place. 

Attach the hanging brackets to the suspension bolts as per the instructions in the figure to the right.

 

Be sure to affix nuts (M8 or M10, 3 pieces in 4 locations) and washers (for M8, outside diameter of 24 to 
28 mm or for M10, outside diameter of 30 to 34 mm: 2 pieces in 4 locations) (to be supplied in the field) 

from both the top and bottom of the hanging brackets on both sides of the unit to secure it in place.

2.  Adjust the height of the unit as desired.
3.  Using a level, verify that the unit has been installed in a level orientation. 

(The unit should be either level or within 1° of slope toward the drain socket.)

Nut (double nut) 
(Field supply)

Suspension bolt (Field supply)

10 - 15 mm

Hanging bracket

Washer (Field supply)

Nut (Field supply)

BS unit

01_EN_3P194121-8U.indd   6

2/21/2014   3:31:06 PM

Summary of Contents for BS4Q14AV1
























Reviews: