background image

English 

17

CAUTION

• 

Use 2-core transmission wiring. 
Using the same wire with 3 or more cores to connect 2 or more indoor units may cause them to stop with 
an error.

• 

When the shield wire is used, be sure to ground the one side of the shield wire. 
The total wiring length is 1500m when shielded wire is used.

• 

Be sure to use ring type crimp style terminals with insulation sleeves to  
connect wires to the power supply terminal block. (

Refer to Fig. 11.

)

• 

Do not use with the power supply terminal block and earth terminal  
connected to wiring for another circuit.

• 

Do not pre-solder stranded wire.

• 

Connect wires securely so that the terminals will not be subjected to external force.

• 

Use an appropriately sized screwdriver to tighten the terminal screws. 
Use of a screwdriver that is too small could damage the screw head and prevent proper tightening.

• 

Overtightening the terminal screws could damage the screw. 
Refer to the table for the terminal screw tightening torque. 

Terminal screw size

Tightening torque (N·m)

M3.5  

(transmission wire terminal block)

0.88 ± 0.08

M4  

(power supply terminal block)

1.31 ± 0.13

M4  

(earth terminal)

1.69 ± 0.17

• 

Never connect power supply wiring to the transmission wiring terminal block. 
Doing so may damage the entire system.

• 

Transmission wiring cannot be branched again after the initial branch.  
(

Refer to Fig. 12.

)

F1 F2

F1 F2

F1 F2

F1 F2

F1 F2

Branch after initial branch

Branch

Fig.  12   

Ring type crimp 
style terminal

Electric wire

Insulation 
sleeve

Fig. 11

01_EN_3P194121-8U.indd   17

2/21/2014   3:31:12 PM

Summary of Contents for BS4Q14AV1
























Reviews: