background image

English 

19

• 

Power supply wiring and earth wires 
Remove the control box cover and connect the power supply wiring to the 
power terminal block (X1M). 
Also connect the earth wire to the earth wire terminal. 
Pass both the power supply wires and the earth wire together through the 
wire through hole (left) into the control box and use the included clamps (2) 
to securely hold the wires in place. 
Be sure to wire the earth wire so that it comes out of the cut out slit in the 
cup washer. 

(Not doing so could cause insufficient earth wire contact, causing the wire 

not to function as a earth.) 
For more information about how much insulation to strip off power wiring, 

refer to the following figure.

L

N

Power wiring (3-core)

130

Cut out slit

Cup washer

Ring type crimp 
style terminal

WARNING

Organize the wiring and securely reattach the control box cover. 

Pinched wires or a loose control box cover could result in electric shock or fire.

CAUTION

• 

When fastening the wire, use the included clamp (2) so as not to apply tensile force to the wire connec-
tion and then securely fasten the wire. 
Also, after the wiring is completed, organize the wiring so that the control box cover does not pop up and 
then properly replace the control box cover.  
Make sure no wires are pinched when replacing the control box cover.  
Always use the wire through hole to protect wires.

• 

Do not pass the transmission wiring and power supply wiring through 
the same locations, and outside of the unit keep them separated by at 
least 50 mm. 
Not doing so could cause the transmission wiring to pick up electric 
noise (external noise) and result in a malfunction or breakdown.

• 

After the wiring work is complete, use sealer (to be supplied in the 

field) to seal closed the wire through hole.

 

(Entry by small animals, etc., could cause a malfunction.)

• As shown in the figure to the right, wrap the transmission wiring 

between each BS unit and indoor unit with finishing tape (to be sup

-

plied in the field).

Gas pipe

Transmission 
wiring

Liquid 
pipe

Finishing tape

Insulation material

01_EN_3P194121-8U.indd   19

2/21/2014   3:31:15 PM

Summary of Contents for BS4Q14AV1
























Reviews: