background image

16 

English 

8-4  Wiring example

Here is shown a wiring example for transmission wiring.

WARNING

Install an earth leakage circuit breaker.

Failure to install an earth leakage circuit breaker may result in electric shock or fire.

• 

Connect terminals F1 and F2 (IN/OUT) on the control Printed Circuit Board in the outdoor unit’s control 

box to terminals F1 and F2 (outdoor unit) on the first BS unit.

F1 F2 F1 F2 F1 F2 F1 F2

F1 F2 F1 F2

F1 F2 F1 F2

F1 F2

F1 F2

F1 F2

F1 F2

F1 F2

F1 F2

F1 F2

F1 F2 F1 F2

L

B

E

D

220-240V

N

Indoor 

unit 

A

Indoor 

unit 

B

Indoor 

unit 

C

Indoor 

unit 

D

Outdoor 

unit

BS unit

BS unit

Outdoor unit

To BS unit

Cooling-dedicated 
unit (Note 1)

Indoor unit 

A

Indoor unit 

B-1

Indoor unit 

B-2 (Note 3)

Indoor unit 

C (Note 2)

Indoor unit 

Indoor unit 

OUT

OUT OUT

IN

Never connect to power supply wiring.

When joining branch pipes

Indoor 

unit

Outdoor 

unit

BS unit

B : earth leakage circuit breaker

Power supply

NOTES 

1. 

Connect the cooling-dedicated unit to the final BS unit’s F1 and F2 terminals (outdoor side).

2.  This wiring example applies when joining the C and D branches and connecting them to indoor units. 

The terminal block to which the transmission wiring is connected can be connected to either indoor unit 
C or indoor unit D. 
However, the DIP switches must be set appropriately. 
For more information about how to set DIP switches, refer to “

9. INITIAL SETTING

”.

3.  The maximum connection number of indoor units per branch is 5 sets.

01_EN_3P194121-8U.indd   16

2/21/2014   3:31:12 PM

Summary of Contents for BS4Q14AV1
























Reviews: