ED72-975
Installation Manual
BRC1E61
39
7.2
Accessories
7.3
Remote controller installation procedure
3P243521-1
4
English
Accessories
2.
The following accessories are included.
W
ood screw
Small screw
Clamp
Operation
manual
Installation
manual
Wiring retainer
(
φ
3.5×16)
(M4×16)
(2 pcs.)
(2 pcs.)
(1 pc.)
(1 pc.)
(1 pc.)
(1 pc.)
Remote controller installation
3.
procedure
Determine where to install the remote controller
.
3-1
Make sure to follow “
1. Safety Precautions
” when determining the location.
Make a wiring through hole on the wall if the wires are taken
3-2
out from the back side.
Set the center of the wall hole
to the center of the wiring thro
ugh hole on the controller
lower case when making the
hole.
F
8-10
External view of the remote controller
Through
hole
F
8-10
Lower case
Through hole
48.5
40
Remove upper case.
3-3
Insert a screwdriver in the recess of lower case to remove the upper case (2 points).
Upper case
Lower case
Screwdriver
Insert and twist the screwdriver
lightly for removal.
Remote controller PC-board is
installed on the upper case.
T
a
ke care
not to damage the PC-board with the
screwdriver
.
T
a
ke care that dust or moisture does
not touch the PC-board of removed
upper case.
If the hole size is too large or the location is not
proper
, the hole may come out from the controller
.
CAUTION
01_EN_3P243521-1.indd 4
2/3/2009 1:19:15 PM
English
3
CAUTION
T
o
avoid leakage and electric shock due to entry of water or insects, fi
ll the wiring through hole with
putty
.
T
o
avoid electric shocks, do not operate with wet hands.
Do not wash the remote controller with water
, as this may result in electric shocks or fi
re.
Install the indoor and outdoor units, power cord and connecting wires at least
1 meter away from
televisions or radios to prevent picture interference and noise.
(Depending on the incoming signal strength, a distance of 1 meter may not be suffi
cient to eliminate
noise.)
Do not install the air conditioner in the following locations:
Where there is a high concentration of mineral oil spray or vapour (e.g. a kitchen).
1.
Plastic parts will deteriorate, parts may fall of
f and water leakage could result.
Where corrosive gas, such as sulphurous acid gas, is produced.
2.
Corroding of copper pipes or soldered parts may result in refrigerant leakage.
Near machinery emitting electromagnetic radiation.
3.
Electromagnetic radiation may disturb the operation of the control system and result in a
malfunction of the unit.
Where fl
ammable gas may leak, where there is carbon fi
bre or ignitable dust suspensions in the
4.
air
, or where volatile fl
ammables such as paint thinner or gasoline are handled.
Operating the unit in such conditions may result in fi
re.
High temperature area or directly fl
amed point.
5.
Heating and/or fi
ring may be caused.
Moist area, or place where may be exposed to water
.
6.
If water enters inside of the remote controller
, electric shock may be caused and inner electronics
may fail.
When remote controller thermo function is used, select the installation location considering the
followings.
A
place where average temperature in the room can be detected.
Ɣ
A
place where is not exposed to direct sunlight.
Ɣ
A
place where is far apart from heat source.
Ɣ
A
place where is not af
fected by outside air due to door opening/closing or the like.
Ɣ
01_EN_3P243521-1.indd 3
2/3/2009 1:19:14 PM
