background image

4 Installation

Installation manual

11

EBLQ+EDLQ011~W1
Daikin Altherma low temperature monobloc
4P522031-1 – 2018.01

Routing

Possible cables (depends on the installed
options)

b

High voltage

▪ Normal kWh rate power supply

▪ Preferential kWh rate power supply

▪ Heat pump convector (option)

▪ Shut-off valve (field supply)

▪ Domestic hot water pump (field supply)

▪ Space heat/cool operation control

c

Main power supply

▪ Main power supply

3

Inside the unit, route the wiring as follows:

b

a

V3

a

W1

a

Power supply cable

b

Cable tie

4

Make sure that the cable does NOT come in contact with sharp
edges.

5

Install the switch box cover.

INFORMATION

When  installing  field  supply  or  option  cables,  foresee
sufficient cable length. This will make it possible to remove/
reposition  the  switch  box  and  gain  access  to  other
components during service.

CAUTION

Do NOT push or place redundant cable length in the unit.

4.4.2

To connect the main power supply

1

Connect the main power supply as follows:

X1M

1 2 3 L N

a

b

V3

1 2 3 L1 L2 L3 N

X1M

a

W1

a

Power supply cable (including earth)

b

Cable tie

4.4.3

To connect the user interface

INFORMATION

▪ If control box EKCB07CAV3 is NOT part of the system,

connect the user interface directly to the outdoor unit.

▪ If control box EKCB07CAV3 is part of the system, you

can  also  connect  the  user  interface  to  the  control  box.
To  do  this,  connect  the  user  interface  to  control  box
terminals X2M/20+21, and then connect the control box
to  the  outdoor  unit  by  connecting  X2M/20+21  to
outdoor unit terminals X5M/1+2.

INFORMATION

For  details  on  how  to  connect  the  user  interface  to  the
control  box,  refer  to  the  installer  reference  guide  or  the
installation manual of the control box.

Summary of Contents for Altherma EBLQ014CAV3





























Reviews: