Daikin ACZ Installation And Maintenance Manual Download Page 2

IM 743-7 • MICROTECH II CHILLER UNIT CONTROLLER 2 

www.DaikinApplied.com

Table of Contents

Table of Contents

Introduction .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3

Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Notice   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Software Revision  . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Limited Warranty  . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Reference Documents . . . . . . . . . . . . . . . . . . . . . . . 3
Hazardous Information Messages . . . . . . . . . . . . . . 4
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Component Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Modbus Network Connector  . . . . . . . . . . . . . . . . . . 5
8-Pin Header  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6

Installation and Mounting  . . . . . . . . . . . . . . . . . . . . . . 6

Field Installation Kit . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing a new Communication Module . . . . . . . . . 6
Replacing a Communication Module . . . . . . . . . . . . 8

Network Configuration

 .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9

Set up the Unit for Network Control  . . . . . . . . . . . . . . 9

Network Setup for Centrifugal Chillers. . . . . . . . . . . 9
Network Setup for all other Chillers . . . . . . . . . . . . . 9

Modbus Network Addressing  . . . . . . . . . . . . . . . . . . . 9

Modbus Network Considerations . . . . . . . . . . . . . . . 9

Additional Modbus Configuration Parameters

. . . . 10

Parts and Service  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 11

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

General  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Network Parameters  . . . . . . . . . . . . . . . . . . . . . . . 11
Network wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Network Performance  . . . . . . . . . . . . . . . . . . . . . . 11

Parts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

© 2022 Daikin Applied, Minneapolis MN. All rights reserved throughout the world

Daikin Applied reserves the right to change any information contained herein without prior notice. The user is responsible for 

determining whether this product is appropriate for his or her application.

Summary of Contents for ACZ













Reviews: