Daihen OTC Welbee WB-P320E, Owner'S Manual

Page: 18 / 150

S
PECIFICATION
P
RODUCT
S
PECIFICATION AND
C
ONFIGURATION
C
HAPTER
2
2-2
2.1.2 Applicable welding mode
This section explains the applicable welding mode (welding method/shielding gas/wire type, and wire
diameter).
2.1.2.1 Standard specification
This section explains the applicable welding mode in the standard specification.
2.1.2.2 Optional specifications
This section explains the welding mode, which is added according to the option (OP-GAS, OP-SUS, OP-
AL, OP-WAVE and OP-STICK).
NOTE
• Each option has label according to the item which is added. This label is used with putting
on the predefined position on the operation panel. Refer to operation manual of each option
for details.
WELDING
METHOD
GAS (*1) WIRE MATERIALS WIRE DIA. (mm) TRAVEL SPEED
Penetration
adjustment
DC
MIG (2.5 CO
2
)
CrNi 0.8/1.0/1.2 (*2) (*3) Enable
DC
PULSE
MAG (20 CO
2
) G3Si1 0.8/1.0/1.2 (*2) Enable
MIG (2.5 CO
2
)
CrNi 0.8/1.0/1.2 (*2) Enable
MIG (Ar) CrNi 1.0/1.2 (*2) Enable
*1: Note that the "collective" voltage adjustment may not meet the appropriate condition if a mixing gas other than those with
the following mixing ratios is used.
MAG (20 CO
2
) : Argon (Ar) 80 % + Carbon dioxide (CO
2
) 20 %
MIG (2.5 CO
2
) : Argon (Ar) 97.5 % + Carbon oxygen (CO
2
) 2.5 %
MIG (Ar) : Argon (Ar) 100 %
*2: Available for applications either of "STANDARD" or "HIGH".
*3: For "STANDARD" mode, the standard mode or extended cable mode (extended mode of power cable) is available.
( 6.7.2.1
-
F1: Standard/Extended cable mode)
Optional
WELDING
METHOD
GAS (*1) WIRE MATERIALS WIRE DIA. (mm) TRAVEL SPEED
Penetration
adjustment
OP-GAS
DC
CO
2
G3Si1 0.8/1.0/1.2 (*2) (*3) Enable
MAG (10 CO
2
)
G3Si1 0.8/1.0/1.2 (*2) (*3) Enable
MIG (2 O
2
) CrNi 0.8/1.0/1.2 (*2) (*3) Enable
DC
PULSE
MAG (10 CO
2
)
G3Si1 0.8/1.0/1.2 (*2) Enable
MIG (2 O
2
) CrNi 0.8/1.0/1.2 (*2) Enable
OP-SUS
DC
CO
2
G3Si1 (Fill) 1.2 STANDARD (*3) Enable
CrNi (Fill) 1.2 STANDARD (*3) Enable
MAG (20 CO
2
)
G3Si1 (Fill) 1.2 STANDARD (*3) Enable
CrNi (Fill) 1.2 STANDARD (*3) Enable
MIG (2 O
2
) CrNi (Ferr) 1.0/1.2 (*2) (*3) Enable
MIG (2.5 CO
2
)
CrNi (Ferr) 1.0/1.2 (*2) (*3) Enable
DC
PULSE
MAG (20 CO
2
)
G3Si1 (Fill) 1.2 (*2) Enable
CrNi (Fill) 1.2 (*2) Enable
MIG (2 CO
2
) CrNi (Ferr) 0.8/1.0/1.2 (*2) Enable
MIG (2.5 CO
2
)
CrNi (Ferr) 0.8/1.0/1.2 (*2) Enable
MIG (100 Ar) CrNi (Ferr) 1.0/1.2 (*2) Enable