Dahua NVR4216-16P-4 Full Manual Download Page 5

Page: 5 / 135

2. How to add and change the setting of the camera

2.1. How to install HDD

Important

：

Please turn off the power before you replace the HDD.

The pictures listed below for reference only.

For the first time install, please be aware that whether the HDDs have been installed.
Please use HDD of 7200rpm or higher.

Usually we do not recommend the PC HDD.

Please follow the instructions below to install hard disk.

○,1 Loosen the screws of the
upper cover and side panel.

②

Fix four screws in the HDD

(Turn just three rounds).

③

Place the HDD in accordance

with the four holes in the bottom.

④

Turn the device upside

down and then turn the
screws in firmly.

⑤

Fix the HDD firmly.

⑥

Connect the HDD cable and

power cable.

⑦

Put the cover in

accordance with the clip and
then place the upper cover

⑧

Secure the screws in the

rear panel and the side

Summary of Contents for NVR4216-16P-4








































































































































Search results

Summary of Contents for NVR4216-16P-4

Reviews:

Related manuals for NVR4216-16P-4

Brands by name

Popular brands

Dahua NVR4216-16P-4, Full Manual

Search results

Summary of Contents for NVR4216-16P-4

Reviews:

Related manuals for NVR4216-16P-4

Brands by name

Popular brands