Dahua NVR4216-16P-4 Full Manual Download

Page: 47 / 135

Figure 4-10

It is to zoom in specified zone of current channel. It supports zoom in function of multiple-

channel.
Click button

, the button is shown as

, see Figure 4-10. Right click mouse system

restores original status.

There are two ways for you to zoom in.

Drag the mouse to select a zone

Put the middle button at the centre of the zone you want to zoom in, and move the

mouse

4.8 How to open audio

Figure 4-11

Note: Please switch to single mode and connect a sound box to the audio out of

HCVR/DVR/NVR; otherwise you cannot hear the voice from front-end IP camera with audio

in.
Click the audio button

to open intercom function, which is shown in the following figure.

4.9 How to snapshot

Summary of Contents for NVR4216-16P-4








































































































































Search results

Summary of Contents for NVR4216-16P-4

Reviews:

Related manuals for NVR4216-16P-4

Brands by name

Popular brands

Dahua NVR4216-16P-4, Full Manual

Search results

Summary of Contents for NVR4216-16P-4

Reviews:

Related manuals for NVR4216-16P-4

Brands by name

Popular brands