background image

DAGON Lighting

 

SPM-12 – controller 

DMX-512 – 12 OUT DC / PWM

 

 

 

5

SPM-12  configuration  described  above  allows  you  to  enter  configuration  codes  without 

the possibility of the subsequent preview, for example to check if the function is active or not. 
If you forget the function the code need to be re-enter. 

 

However,  reading  the  DMX  address  value  can  be  very  useful,  that  is  why  there  was 

introduced the  possibility of viewing the address in the driver SPM-12, see point 2.2. 
 
 

2.2. Preview of DMX address SPM-12 driver.

 

 

To  preview  the  DMX  address  of  controller  the  button  PLUS  need  to  be  pressed  for  1 

second. Green diode will light off and yellow will light on.  

 

Preview of first digit of DMX-512 address:

 

  Green diode will blink as many times as the first digit of DMX address is from 0 to 5. 
  Than yellow diode blinks once (light off for half a second and light on again) 
  which is the signal for display the second digit. 

 

Preview of second digit of DMX-512 address:

 

  Green diode will blink as many times as the second digit of DMX address is from 0 to 9. 
  Than yellow diode blinks once (light off for half a second and light on again) 
  which is the signal for display the third digit. 

 

Preview of third digit of DMX-512 address:

 

  Green diode will blink as many times as the third digit of DMX address is from 0 to 9. 
  Yellow diode will light off – DMX address is read off. 
 

After the 2 seconds from reading DMX address in SPM-12 controller starts regular work, 

which means steering the outputs Q1-Q12 in requested work by the control codes. 
 

Summary of Contents for SPM-12









Reviews: