background image

10

Attaching the bracket to a concrete floor:

• 

Drill four (4) 3/8” diameter countersink holes through 

any existing floor covering to the concrete slab below.

• 

Drill the 4 holes for the anchors 1 1/4” (3.2 cm) deep 

into the concrete slab using a 3/16” masonry bit. This 

hole length is longer than the anchor, but is required 

for proper installation. Clear the holes of dust and any 

other material. Tap each anchor into the hole until the 

anchor top is flush with the top of the concrete slab. 

Position the anti-tip bracket holes over the anchor 

holes. Insert the screws through the four (4) holes 

in the base of the bracket and thread them into the 

anchors. Be sure the screw threads fully engage the 

anchor body. Tighten the screws into place.

Attaching the bracket to a wood floor:

• 

If there is ceramic, asphalt or other hard floor covering 

over the wood below, drill four (4) countersink holes to 

allow access to the wood below for drilling pilot holes.

• 

Drill four (4) pilot holes into the wood floor using a drill 

bit (1/16” dia. for #8 screws, 1/8” dia. for #12 screws). 

Position the anti-tip bracket holes over the holes in the 

floor. Insert the screws into the wood and tighten into 

place.

CL

Installing the Anti-Tip Bracket on the Floor 

(cont.)

Four (4) plastic anchors are provided along with three sizes 

(4 each) of #8 or #12 Phillips head screws for attaching 

the anti-tip bracket to the floor. Use both the anchors and 

four (4) of the #8 screws when attaching the bracket to a 

concrete sub-floor. Do not use the anchors when attaching 

to a wood sub-floor.

1.  Determine the location of the range center line and 

front panel when the range is in its final position 

based on the 

Product Dimensions

 on page 4 

and the actual cabinet/cutout dimensions used for the 

installation.

2.  Determine the required position of the anti-tip bracket, 

based on the diagram, bottom right. Mark the four (4) 

mounting hole locations on the floor with a pencil.

3.  Determine the screw size required. The minimum full 

thread depth (portion of screw threaded into wood/slab) 

for wood is 3/8” (1 cm) and 5/8” (1.6 cm) for concrete. 

See the table below to select the correct screw size.

Sub-Floor Type/ 

Floor Covering Thickness

Screw Size

Concrete or wood sub-floor, 

no floor covering over top.

#8 x 1 *

Concrete or wood sub-floor, 

floor covering up to 1/4” thick

#8 x 1 *

Concrete or wood sub-floor, 

floor covering over 1/4” and 

up to 1/2” thick

#8 x 1 1/4 *

Wood sub-floor, floor covering 

over 1/2” and up to 1 3/16” 

thick

#12 x 1 3/4 *

Concrete sub-floor under floor 

covering over 1/2” thick

Must be purchased

separately **

Wood sub-floor, floor covering

over 1 3/16” thick

Must be purchased

separately **

* Included with range
** Determine required depth based on information in step 3 

and purchase from local hardware store.

Installation Instructions

#8 x 1”, #8 x 1 1/4” 

or #12 x 1 3/4

screw, 4 places

(see text)

Anchor, 4 places:

use for concrete

floor only

Front hole

Anti-tip bracket

front hole 

locations

Range front

panel

Range center line

10 3/8” (26.4 cm)

 2 3/16” (5.6 cm)

Cabinet

face below

countertop

22 1/2”

 

(57.2 cm)

Top View

Anti-tip 

bracket

Sub-floor

Floor

covering

Concrete 

anchors shown, 

do not use for 

wood sub-floor

Screws attached 

to sub-floor below 

floor covering

Side View

Summary of Contents for DR30GS

























Reviews: