background image

16

Installation Instructions

Verifying Proper Operation

 WARNING

Before operating the range, read the accompanying use 

and care manual completely.

1.  Before beginning the test procedure, make 

sure all range control valves are in the 

“OFF”

 

position, and all burner rings, burner caps and 

grates are properly positioned on the spill tray. 

2.  Turn on the gas supply at the shut-off valve.
3.  Connect the power cord to the electrical outlet. When 

the range is first connected, the oven indicator light 

flashes on and off for about 10 seconds while the 

range’s circuitry starts up. Wait for the light to stop 

flashing before going to step 4.

4.  Test the left front burner on the cooktop 

by pushing in and turning the control knob 

counterclockwise to the 

HIGH

 position. 

The igniter for the left front burner will 

spark continuously. It may take up to 4 

seconds for the burner to ignite, at which time the 

ignitor will stop sparking. If ignition does not occur 

within 4 seconds, turn off the knob, wait for at least 5 

minutes to allow any gas to dissipate, then repeat this 

ignition test. When the burner ignites, rotate the knob 

counterclockwise from 

HIGH 

to 

LOW

 to adjust the 

flame height progressively. When installed properly, 

the flame will be steady. It will also have a sharp, blue 

inner cone that will vary in length proportional to the 

burner size. LP gas units may have small yellow tips at 

the end of the flames, which is normal. 

5.  Repeat ignition test for the remaining cooktop burners. 

Make sure the knobs light when in the 

HIGH

 position.

6.  After testing all the cooktop burners, turn them all off.
7.  Open the oven door. Test the oven light by turning on 

the light switch on the right side of the control panel.

8.  Turn on the convection fan switch. You should hear the 

convection fan, located behind the screen at the back 

of the oven, come on.

9.  With the oven door open, turn the oven control knob 

to the 400 degree position. Both the knob itself and 

the oven ON indicator light next to the knob should 

illuminate. Within 60 seconds you should hear the bake 

burner ignite below the oven floor. It should begin to 

give off heat. 

10. Turn the oven control knob to the 

BROIL

 position. The 

bake burner should turn off. Both the oven control knob 

and the oven 

ON

 indicator light should be illuminated. 

Within 60 seconds the broil burner on the ceiling of the 

oven should ignite and begin to give off heat.

11.  Turn the oven knob to the 

OFF

 position.

If the range does not operate properly, follow these 

troubleshooting steps:

1.  Verify that the circuit breaker for the range electrical 

outlet is on and not tripped. Make sure the power cord 

is connected.

2.  Make sure the gas supply valve is in the on position 

and that the main gas valve to the building is open.

3.  Check to see if the oven burner light flashes on and 

off once a second. If it does, repair by an authorized 

service technician is required.

4.  Repeat the above tests.
5.  If the appliance still does not work, contact Dacor 

Distinctive Service at (800) 793-0093 ex. 2822. Do not 

attempt to repair the appliance yourself. Dacor is not 

responsible for the cost of correcting problems caused 

by a faulty installation.

OFF

HIGH

Normal Flame

Summary of Contents for DR30GS

























Reviews: