background image

4

Installation Specifications

Product Dimensions

1 1/8” (2.9 cm)

DR30GI[F]S:

1/4” (6.4 mm)

thick top trim

Front of open door
Front of handle

Front panel

Rear of front panel

Backguard thickness

26 1/8” (66.4 cm)

28 9/16” (72.5 cm)

Front of knobs

28” (71.1 cm)

24” (61.0 cm)

3” (7.6 cm)

backguard*

DR30G[F]S:

Full stainless 

steel side panels

DR30GI[F]S:

3 1/2” (8.9 cm)

partial stainless 

steel side panels

(removable)

External handle 

shown, some models 

have integral handle

(see inside cover)

Grates extend

1” above trim

6” (15.2 cm)

backguard*

1 3/4” (4.4 cm) backguard*

*

See table for compatibility

Product width:

29 7/8” (75.9 cm) 

NOTE:

 Models DR30GS and 

DR30GFS are not compatible 

with a raised vent.

35”

(88.9 cm)

to

37”

(94.0 cm)

9” (22.9 cm)

Backguard*

46 3/4” (118.7 cm)

Overall Dimensions - Side View

Available Backguards

*

Part Number

Description

Compatibility

AER30GLBG

Low profile  

(1 3/4 inch) 

Standard on models DR30GIS, DR30GIFS

Optional on models DR30GS, DR30GFS

AERB30G03

3 Inch

Optional on models DR30GS, DR30GFS

NOT compatible with models DR30GIS, DR30GIFS

AERB30G06

6 Inch

Standard on models DR30GS, DR30GFS

NOT compatible with models DR30GIS, DR30GIFS

AERB30G09

9 Inch

Optional on models DR30GS, DR30GFS

NOT compatible with models DR30GIS, DR30GIFS

Only backguard model AER30GLBG is compatible with a raised vent.

All tolerances: ±1/16” (±1.6 mm), unless otherwise stated

Summary of Contents for DR30GS

























Reviews: