background image

6

Installation Specifications

 WARNING

• 

Failure to meet or exceed the maximum 

and minimum dimensions/clearances stated 

may result in a fire hazard.

• 

To eliminate the risk of burns or fire by 

reaching over heated surface units, cabinet 

storage space located above surface units 

should be avoided.

• 

Carefully check the location where the range 

is to be installed. For best performance, the 

range should be placed away from drafts 

that may be caused by doors, windows and 

heating and air conditioning outlets.

• 

To reduce the risk of personal injury and 

to reduce accumulated smoke in the room, 

Dacor strongly recommends installing a 

range hood or raised vent. 

• 

A range hood should project horizontally 

a minimum of five (5) inches beyond the 

face of the cabinets. If installing a range 

hood, see the range hood specifications for 

minimum clearances.

• 

If cabinet storage space is to be provided 

directly above the range, the risk of personal 

injury may be reduced by installing a range 

hood.

• 

If installing a raised vent, install only Dacor 

model ERV3015.

• 

The range may be installed flush to the rear 

wall. See diagram and notes for rear wall 

surface requirements. It is not necessary to 

install non-combustible materials behind the 

range below the countertop height.

• 

Regardless of the type of back wall surface, 

the range must not be installed or operated 

without the backguard in place.

• 

Any openings in the wall behind the 

appliance or in the floor underneath it must 

be sealed.

Cabinet Layout

Note 2

B

A

Back wall

immediately

behind range

6

Top of

finished

counter

13” (33.0 cm)

max.

4

14” (35.6 cm) 

min.

4

C

Suggested 

location of 

utilities

3

Note 5

Note 1

A*

B

C

30” 

minimum 

(76.2 cm)

36” (91.4 cm) 

recommended  

30” (76.2 cm) 

minimum

37” 

(94.0 cm) 

maximum

Freestanding Installation Cabinet Cutout Dimensions - Models DR30GS, DR30GFS, DR30GIS and DR30GIFS

*See cutout dimensions on facing page for 

self-rimming installations.

All tolerances: +1/16” (+1.6 mm), -0 

unless otherwise stated

1 30” (76.2 cm) min. vertical clearance from top of range grates to bottom of uncovered wood or metal cabinet. 24” (61 cm) min. 

clearance if bottom of wood or metal cabinets are protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no 

less than No. 28 MSG sheet steel 0.015” (0.04 cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. 30”  

(76.2 cm) min. clearance between top of range grates and bottom of unprotected wood or metal cabinet. If installing range hood, check 

the hood specifications for minimum required clearances.

2 Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See 

Product Dimensions

.

3 Consult local code and page 9 for requirements.

4 This specification not applicable for cabinets more than a horizontal distance of 10” (25.4 cm) from edge of range.

5 10” (25.4 cm) min. to combustible sidewalls above range (both sides).

6 Non-combustible surface required for models DR30GIS and DR30GIFS up to vertical distance specified in note 1 or range hood, 

whichever is lower. Non-combustible surface recommended, but not required, for models DR30GS and DR30GFS. 

Summary of Contents for DR30GS

























Reviews: