PORTUGUÊS
99
7.6
Certificar-se de que a instalação está equipada com um sistema de drenagem para o ar e de que o
vaso de expansão (se previsto) está instalado antes da boca de aspiração. Quando, ao contrário, a
bomba está instalada na compressão de um circuito de vaso aberto, controlar que o tubo de
segurança esteja ligado antes da bomba.
7.7
Montar a bomba na instalação de forma a que os tubos metálicos não transmitam para o corpo da
bomba esforços ou tensões excessivas que podem criar rachas e rupturas.
7.8
Para evitar a transmissão do ruído ou de eventuais vibrações, aconselha-se a montagem de
juntas
anti-vibrações
nas bocas de aspiração e compressão.
8.
LIGAÇÃO ELÉCTRICA:
Atenção: cumprir sempre as normas de segurança!
Respeitar rigorosamente os esquemas eléctricos referidos no
interior da caixa da régua de bornes e os referidos na pág. 5
deste manual.
8.1
As ligações eléctricas devem ser realizadas por um electricista experiente que possua
os requisitos exigidos pelas normas em vigor (ver o parágrafo 6.1).
É preciso seguir minuciosamente as prescrições previstas pela empresa de
distribuição da energia eléctrica.
No caso de motores trifásicos com arranque estrela-triângulo, é preciso garantir que o tempo de
comutação entre estrela e triângulo seja o menor possível e que entre na tabela 8.1 da pág. 110.
8.2
Antes de ter acesso à régua de bornes e agir na bomba, verificar se
foi desligada a corrente
.
8.3
Verificar a tensão da rede antes de realizar qualquer ligação. Se corresponde à nominal, proceder à
ligação dos fios à régua de bornes
dando prioridade ao de ligação à terra. (Fig. D)
8.4
CERTIFICAR-SE DE QUE A INSTALAÇÃO DE LIGAÇÃO À TERRA É EFICIENTE E
DE QUE É POSSÍVEL REALIZAR UMA LIGAÇÃO ADEQUADA
.
8.5
As bombas devem estar sempre ligadas a um interruptor externo.
8.6
Os motores monofásicos estão providos de protecção termo-amperimétrica incorporada e podem
ser ligados directamente à rede.
8.7
Os motores trifásicos devem estar protegidos por especiais protectores com ajuste adequado à
corrente nominal.
8.8
Nas instalações em que está prevista a execução acoplada, para possibilitar a continuidade do
serviço, aprontar cablagens e interruptores separados por cada bomba.
9.
ARRANQUE
9.1
O fluido contido na instalação, além que em alta temperatura e
pressão, também pode encontrar-se em forma de vapor!
PERIGO DE QUEIMADURAS
Pode ser perigoso até só tocar na bomba ou em partes da
instalação.
Antes do arranque é indispensável encher a instalação com água e drenar o ar. Drenar do corpo da
bomba o ar residual por meio da especial torneira de purga (não fornecida para as versões ALM
200 - ALP 800) até sair apenas água
(Fig. E)
. Isso para que a bomba comece a funcionar logo de
maneira regular e para que o empanque mecânico resulte bem lubrificado.
O funcionamento sem
líquido provoca danos irreparáveis no empanque mecânico.
9.2
Ligar a tensão e verificar se o sentido de rotação nos motores trifásicos está correcto: olhando o
motor do lado da ventoinha, deverá ocorrer em sentido horário
(Fig. F)
. Caso contrário, inverter
entre eles dois quaisquer dos condutores de fase, depois de desligada a bomba da rede de
alimentação.
9.3
Com a electrobomba em funcionamento, verificar a tensão de alimentação aos grampos do motor,
que não deve diferenciar-se de +/- 5% do valor nominal (
Fig. G
).
9.4
Com o grupo que funciona em regime, verificar que a corrente absorvida pelo motor não exceda a
nominal.
Summary of Contents for ALM 200
Page 2: ......
Page 69: ...67 7 6 7 7 7 8 8 5 8 1 6 1 8 1 110 8 2 8 3 D 8 4 8 5 8 6 8 7 8 8 9 9 1 ALM 200 ALP 800 E 9 2 F...
Page 118: ...116...
Page 119: ...117...