background image

2

Frame Bracket

Quantities vary by screen size
Screens 80" and smaller viewing width = 3
Screens over 80" to 96" viewing width = 4
Screens over 96" viewing width = 6

Quantity Included 

________________________________________________

Included Hardware

Large Wall Bracket (47" Long) 
Installation screws not included

Quantities vary by screen size: 
Screens 80" and smaller viewing width = 1 
Screens over 80" to 96" viewing width = 2 
Screens over 96" viewing width = 3

Quantity Included

 ___________________________

Small Wall Bracket (8" Long) 
Installation screws not included

Quantity = 1. Only for screens 80" and smaller viewing width.

Quantity Included

 ___________________________

Side Frame Bracket (Left and Right)

Screens 90" and larger in viewing height = 2 
Screens with 2-piece side frame rails quantity = 2

Quantity Included

 ___________________________

Snap Stud
Quantity Included

 ___________________________

#10 Screw
Quantity Included

 ___________________________

Important Safety Instructions

When using your video equipment, basic safety precautions 
should always be followed, including the following:

1.   Read and understand all instructions before using.

2.  Failure to provide adequate structural strength for this 

component can result in serious personal injury or damage to 
equipment! It is the installer’s responsibility to make sure the 
structure to which this component is attached can support the 
weight of all equipment. Reinforce the structure as required 
before installing the component.

3.  Use this projection screen only for its intended use as described 

in these instructions. Do not use attachments not 
recommended by the manufacturer.

Save These Instructions

Disclaimer

Milestone and its affiliated corporations and subsidiaries 
(collectively "Milestone"), intend to make this manual accurate 
and complete. However, Milestone makes no claim that the 
information contained herein covers all details, conditions or 
variations, nor does it provide for every possible contingency in 
connection with the installation or use of this subject to change 
without notice or obligation of any kind. Milestone makes no 
representation of warranty, expressed or implied, regarding the 
information contained herein. Milestone assumes no 
responsibility for accuracy, completeness or sufficiency of the 
information contained in this document.

Da-Lite® is a registered trademark of Milestone AV Technologies. 
All rights reserved.

Summary of Contents for Da-Snap Wrap Around Screen









Reviews: