D-Link DWS-1008 Page 16 Installation Manual Download

Page: 16 / 16

D-Link Systems, Inc.

DWS-1008 Install Guide

Contacting Technical Support

Technical Support

D-Link’s website contains the latest user documentation and software updates

for D-Link products.
D-Link provides free technical support for customers within the United States

and Canada for the duration of the product’s warranty period.
U.S. and Canadian customers can contact D-Link Technical Support through

our website or by phone.

United States

Telephone

(877) 453-5465
Monday through Friday 8:00am to 5:00pm PST

World Wide Web

http://support.dlink.com

E-mail

[email protected]

Canada

Telephone

(800) 361-5265
Monday through Friday, 7:30am to 9:00pm EST.

World Wide Web

http://support.dlink.ca

E-mail

[email protected]

Version 1.0

Revised 12/15/2005

6DWS1008ML01G

Software and speciﬁ cations subject to change without notice.

Summary of Contents for DWS-1008

















Search results

Summary of Contents for DWS-1008

Reviews:

Related manuals for DWS-1008

Brands by name

Popular brands

D-Link DWS-1008, Installation Manual

Search results

Summary of Contents for DWS-1008

Reviews:

Related manuals for DWS-1008

Brands by name

Popular brands