D-Link DWL-3200AP - AirPremier - Wireless Access Point Product Manual Download

Page: 12 / 113

DWL-3200AP User’s Manual

D-Link Systems, Inc.

Getting Started

Connecting

PoE

(Power over Ethernet)

Connect one end of an Ethernet cable (included with your package) to
the

LAN port

on the DWL-3200AP and the other end of the Ethernet

cable to the port labeled

P+DATA OUT

on the PoE base unit.

Connect another Ethernet cable from the

DATA IN

port on the PoE

base unit to your router/switch, using a straight through cable, or to
a PC, using a crossover cable.

Attach the power adapter to the connector labeled

POWER IN

the PoE base unit. Attach the power cord to the power adapter and
into an electrical outlet.

Step 1

Step 2

Step 3

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point


















































































































Search results

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point

Reviews:

Related manuals for DWL-3200AP - AirPremier - Wireless Access Point

Brands by name

Popular brands

D-Link DWL-3200AP - AirPremier - Wireless Access Point, Product Manual

Search results

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point

Reviews:

Related manuals for DWL-3200AP - AirPremier - Wireless Access Point

Brands by name

Popular brands