D-Link DWL-3200AP - AirPremier - Wireless Access Point Product Manual Download

Page: 28 / 113

DWL-3200AP User’s Manual

D-Link Systems, Inc.

Using the Conﬁguration Menu

Advanced > Performance

Wireless Band:

Data Rate:*

Beacon Interval:

DTIM:

Fragment Length:

IEEE 802.11g

The

Data Rates

are Auto, 1Mbps, 2Mbps, 5.5Mbps, 6Mbps, 9Mbps,

11Mbps, 12Mbps, 18Mbps, 24Mbps, 36Mbps, 48Mbps, 54Mbps.

Beacons are packets sent by an access point to synchronize a
network. Specify a beacon interval value. The default (100) is
recommended.

*”Maximum wireless signal rate based on IEEE Standard 802.11a and 802.11g speciﬁcations. Actual data throughput will vary.

Network conditions and environmental factors, including volume of network trafﬁc, building materials and construction, and network

overhead lower actual data throughout rate.”

(Delivery Trafﬁc Indication Message) -

Select a setting between 1and

255.

is the default setting. DTIM is a countdown informing clients of

the next window for listening to broadcast and multicast messages.

The fragmentation threshold, which is speciﬁed in bytes, determines
whether packets will be fragmented. Packets exceeding the 2346
byte setting will be fragmented before transmission. 2346 is the
default setting

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point


















































































































Search results

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point

Reviews:

Related manuals for DWL-3200AP - AirPremier - Wireless Access Point

Brands by name

Popular brands

D-Link DWL-3200AP - AirPremier - Wireless Access Point, Product Manual

Search results

Summary of Contents for DWL-3200AP - AirPremier - Wireless Access Point

Reviews:

Related manuals for DWL-3200AP - AirPremier - Wireless Access Point

Brands by name

Popular brands